漿狀油墨檢測

漿狀油墨檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 13217.3-2022油墨細度檢驗方法

本文件描述了油墨細度的檢驗方法。本文件適用于漿狀油墨和液體油墨的產品。

GB/T 18723-2002印刷技術 用黏性儀測定漿狀油墨和連接料的黏性

本標準規定了漿狀油墨及其連接料黏性的通用測定方法。 本標準適用于在正常環境條件下，在測試過程中揮發性低且不發生反應的油墨的黏性測定。

GB/T 22467.2-2008防偽材料通用技術條件.第2部分:防偽油墨和印油

GB/T 22467的本部分規定了各類防偽油墨和印油的術語和定義，分類，要求，試驗方法，檢驗規則，標志、標簽、包裝、運輸和貯存。本部分適用于各類防偽油墨和防偽印油。本部分也適用于指導各類防偽油墨和防偽印油產品標準的編寫。

GB/T 22770-2008印刷技術 用落棒式粘度計測定漿狀油墨和連接料的流變性

本標準規定了在常溫條件下測定不會發生反應的漿狀油墨和連接料的粘度和屈服值的測定方法。本標準適用于表觀粘度在2 Pa?s-200 Pa?s漿狀油墨及其連接料的粘度和屈服值的測定。

GB/T 30329.1-2013印刷技術 四色印刷油墨顏色和透明度 第1部分:單張紙和熱固型卷筒紙膠印

GB/T 30329的本部分規定了四色膠印用原色油墨在膠印打樣和印刷過程中應滿足的顏色和透明度特性,同時規定了印刷條件(使用實驗室用印刷適性儀)、定義承印物和確保一致性的測試方法。本部分適用于單張紙、熱固型卷筒紙和光固化膠印。本部分不適用于熒光油墨,未指定顏料(或光譜特性,提示性信息除外),從而使不同顏料優化組合也可以達到本部分規定的色度要求。

GB/T 38153.1-2019印刷技術 測試印樣的實驗室制備 第1部分:漿狀油墨

GB/T 38153的本部分規定了用漿狀油墨制備印樣的實驗室方法(如用于平版印刷和凸版印刷的油墨)。這種印刷樣品適用于以反射為基礎的測量，如色度和反射密度，以及用于耐光性的測試，同時還適用于印刷油墨和/或承印物的力學性能和耐化學性能測試。

QB/T 1865-2014膠印輪轉冷固型油墨

本標準規定了膠印輪轉冷固型油墨的產品分類、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。本標準適用于膠印輪轉印刷機在膠版、凸版、新聞卷筒紙及非涂層紙上印刷使用的膠印輪轉冷固型油墨。

QB/T 2025-2013平版印鐵油墨

本標準規定了平版印鐵油墨的分類、要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存。本標準適用于在單、雙或多色印鐵膠印機上使用的,在平版印刷的鍍錫(鉻)薄鋼板包裝裝潢印刷品或平版印刷的鋁材包裝裝潢印刷品上印刷的平版印鐵油墨。

QB/T 2624-2012單張紙膠印油墨

本標準規定了單張紙膠印油墨(啞光型、合成紙型油墨除外)的產品分類、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。本標準適用于在單、雙或多色膠印機上使用的,在紙張、薄膜等承印物上印刷圖片及商標等膠印單張紙油墨。

QB/T 5192-2017廣色域單張紙膠印油墨

本標準規定了廣色域單張紙膠印四色油墨的術語和定義、要求、試驗方法、檢驗規則和標志、包裝、運輸和貯存。本標準適用于在單、雙或多色膠印機上使用的，在紙張等承印物上印刷圖片及商標等廣色域單張紙膠印油墨。

QB/T 5193-2017全植物油膠印油墨

本標準規定了全植物油膠印油墨的術語和定義、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。本標準適用于紙張印刷使用的全植物油單張膠印油墨，不包括紫外線固化膠印油墨。

QB/T 5194-2017無水膠印油墨

本標準規定了無水膠印油墨的術語和定義、分類、要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存。本標準適用于普通無水膠印油墨以及紫外光固化無水膠印油墨。

ISO 2834-1-2020印刷技術. 測試印樣的實驗室制備. 第1部分: 漿狀油墨

This document specifies a test procedure for the preparation of test prints on paper, board, metals, foils and other suitable substrates using paste inks, such as for offset and letterpress printing, using electrically driven IGT-type and prüfbau-type printability testers. This document describes the procedure for reference optical density and reference ink film thickness. This document describes the method as used on the current models of testers. Most of the described procedures are also applicable in analogy to the older models but can require additional steps to be executed or recalculation of the settings to make them conform to this document

ASTM D7680-2010用電力驅動適印性測定儀制備漿狀油墨印刷品的標準操作規程

It is generally recognized that the best method for evaluating printing properties of ink-substrate combinations is by actual printing. this practice provides a convenient method for preparing repeatable laboratory prints at realistic conditions of printing speed, printing pressure and ink film thickness. This practice is useful for quality control, specification acceptance between producer and user, product development and research. Printed samples have found widespread applications for color matching, gloss-ink holdout and other appearance properties, permanency, abrasion, drying time and many other tests of interest to the printing ink, paper and allied industries.1.1 This practice describes the procedure for preparing laboratory prints of paste printing inks using a motor-driven printability tester. 1.2 This practice covers printability testers of four different designs, referred to as Tester A, B, C, and D. These testers feature x201C;push-buttonx201D; control of printing speed and pressure and facilitate measurement of exact ink film thickness. 1.3 This practice is intended primarily for lithographic and letterpress inks that dry by oxidation or penetration. With appropriate drying or curing equipment, it is also applicable to other systems such as heat-set or energy curable. 1.4 This practice is applicable to the preparation of single-color solid-area prints by dry offset (also know as letterset) or by letterpress on any flat surface including paper, paperboard, plastic film, textiles, and metal. 1.5 The values stated in SI units are to be regarded as the standard. The only other unit of measurement used is fpm. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TS ISO 12634-2003印刷技術. 用黏性儀測定漿狀油墨和連接料的黏性

This standard specifies the procedure for determining the tack value of pasta inks and vehicles which have low volatility and are unreactive under normal room conditions during the span required for testing

TS ISO 12644-2002用落棒黏度計對漿狀油墨和載色劑的流變特性進行圖像技術測定

This standard specifies the procedure for determining the viscosity and yield valve of paste inks and vehicles which are unreaktive under normal room conditions.

ABNT NBR ISO 12634-2004印刷技術 - 漿狀油墨和車輛粘性旋轉粘性計測定

Specifies the procedure for determining the tack value of paste inks and vehicles which have low volatility and are unreactiv under normal conditions during the time span required for testing. Contains a description of the rotary tackmeters most commonly used.

ABNT NBR ISO 12644-1999印刷技術 - 漿狀油墨和車輛的流變性能測定下降桿粘度計

Contains the procedure for determining the viscosity of paste inks and vehicles which are unreactive under normal room conditions. Applicable to inks in the apparent viscosity range of 2 Pas to 200 Pas.