石油和天然氣工業管線輸送系統用全焊接球閥檢測

石油和天然氣工業管線輸送系統用全焊接球閥檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 21412.1-2010石油天然氣工業 水下生產系統的設計與操作 第1部分：一般要求和推薦做法

本部分制定了整套水下生產系統從設計到廢棄各個階段的一般要求和推薦做法，作為一個綱領性文件用于指導和制定涉及到水下生產系統各個組成部分更為詳細要求的子系統標準。同時，對于子系統標準內未包括的某些部分，如系統設計、結構、管匯、吊裝設備、顏色和標記等，也給出了較為詳細的要求。對那些應用范圍有限的特種設備，如密閉在干式艙中的組合式采油樹、采油樹和管匯等，這里未做專門討論，但本部分中的相關條款同樣適用于這類設備。

GB/T 21412.15-2017石油天然氣工業 水下生產系統的設計和操作 第15部分:水下結構物及管匯

GB/T 21412的本部分在公認及廣泛接受的工業規范及標準框架內，提出水下結構物及管匯的推薦做法。因此，它并不取代或排除其他工業規范規定的任何要求。本部分適用于對水下油氣生產及水下注入進行壓力控制的水下管匯及基盤。水下生產系統實例見圖1。本部分涵蓋下列設備：a)　水下生產系統結構部件和配管系統：——生產及注入管匯；——模塊化和集成的單衛星井及多井基盤；——水下處理及水下增壓站；——出油(氣)立管基座以及外輸立管基座(FRB，ERB)；——管道終端管匯(PLEM)；——管道終端(PLET)；——T型及Y型連接；——水下隔離閥結構物(SSIV)。b)　水下生產系統結構部件：——水下控制和分配結構物；——其他水下結構物。c)　與上述設備相關的保護結構。下列部件及其應用不在本部分范圍內：——管道及管匯閥門；——管道及連接器；——油嘴；——生產控制系統。與上述內容有關的一般信息可從其他規范處獲取，如13628-1及API Spec 2C等。

GB/T 23803-2009石油和天然氣工業 海上生產平臺管道系統的設計和安裝

本標準給出了石油和天然氣工業海上生產平臺新建管道系統的設計和安裝的低要求和指南。管道系統的高壓力高達69000kPa(G)，在溫度范圍內對材料的要求滿足ASME B31.3的要求。

GB/T 30818-2014石油和天然氣工業管線輸送系統用全焊接球閥

本標準規定了石油和天然氣工業管線輸送系統用全焊接球閥的術語和定義、結構型式和參數、技術要求、材料、試驗方法和檢驗規則、標志、包裝和儲運。本標準適用于公稱壓力PN16~PN160或Class150~Class900、公稱尺寸DN50~DN1500或NPS2~NPS60;介質為原油、成品油和天然氣;管線輸送系統用的法蘭連接和焊接連接全焊接球閥。

GB/T 34275-2017壓力管道規范 長輸管道

本標準規定了長輸(油氣)商品介質管道(GA類)建設、投產，在役管道的運行、維修及檢驗等技術要求。本標準適用于長輸管道建設的設計、材料、安裝、無損檢測、投產和在役管道的運行、維修及檢驗。本長輸管道系指產地、儲存庫、用戶間的用于輸送(油氣)商品介質的管道。本標準適用的管道系統范圍見圖1所示。油氣田集輸管道符合本標準的相關條件的可執行本標準。本標準不適用于公用管道(GB類)、工業管道(GC類)、動力管面(GD類)；也不適用于其他類型的管道，如電氣(電訊)專用的管道、軍事裝備和核設施的管道、海上設施和礦井的管道、移動設備上的管道、石油、天然氣、地熱等勘探和采掘裝置的管道、城鎮的門站后所屬的燃氣管網。

GB/T 38202-2019全焊接球閥的安裝使用維護方法

本標準規定了石油和天然氣工業管線輸送系統用全焊接球閥的安裝、使用、維護和檢修的方法。本標準適用于公稱壓力PN16~PN160、公稱尺寸DN50~DN1 500，壓力等級Class150~Class900、公稱尺寸NPS2~NPS60，介質為原油、成品油和天然氣的管線輸送系統用法蘭連接和焊接連接全焊接球閥(以下簡稱球閥)。

GB 50251-2015輸氣管道工程設計規范

本規范適用于陸上新建、擴建和改建輸氣管道工程設計。

GB 50349-2015氣田集輸設計規范

本規范適用于陸上氣田、灘海陸采氣田和海上氣田陸岸終端集輸工程設計。

GB 50350-2015油田油氣集輸設計規范

本規范適用于陸上油田、灘海陸采油田和海上油田陸岸終端油氣集輸工程設計。

GB 50424-2015油氣輸送管道穿越工程施工規范

本規范適用于新建或改、擴建的輸送原油、天然氣、煤氣、成品油等管道穿越障礙物工程的施工。

CECS 419-2015中小型給水泵站設計規程

本規程適用于新建、擴建或改建的中小型給水泵站的設計。

CJJ/T 104-2014城鎮供熱直埋蒸汽管道技術規程

本規程適用于工作壓力小于或等于2.5MPa，溫度小于或等于350°C，直接埋地敷設的鋼質外護蒸汽保溫管道的設計、施工、驗收及運行維護。

SH/T 3059-2012石油化工管道設計器材選用規范

本規范規定了石油化工管道材料的選用、管道組成件的選用要求和計算方法。本規范適用于石油化工裝置中公稱壓力不大于PN 420 (CL2500)、設計溫度不超過材料允許使用溫度范圍的管道組成件的選用。本規范不適用于非金屬管道。

SY/T 0612-2014高含硫化氫氣田地面集輸系統設計規范

本規范規定了高含硫化氫氣田地面集輸系統設計原則，適用于天然氣中硫化氫含量大于或等于5% (體積分數)的新建、擴建和改建工程的設計。

建標 114-2009輸油管道工程項目建設標準

本建設標準適用于陸上新建輸油管道工程。改、擴建輸油管道工程可參照執行。符合管輸標準的煤層氣輸送管道工程可參照執行。

EN ISO 13628-1-2005石油和天然氣工業.水下采油系統的設計和操作.第1部分:一般要求和建議 ISO 13628-1-2005

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment.This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells.This part of ISO 13628 and its related subsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.If requirements as stated inThis part of ISO 13628 are in conflict with, or are inconsistent with, requirements as stated in the relevant complementary parts of ISO 13628, then the specific requirements in the complementary parts take precedence.

DIN EN 14161-2015石油和天然氣工業.管道運輸系統(ISO 13623-2009已修訂);德文版本EN 14161-2011+A1-2015

This European Standard specifies requirements and gives recommendations for the design, materials, construction, testing, operation, maintenance and abandonment of pipeline systems used for transportation in the petroleum and natural gas industries. It applies to pipeline systems on land (see exclusion below) and offshore, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for the purpose of its connection. On-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances are excluded from the scope of this European Standard.

DIN EN ISO 13628-11-2008石油和天然氣工業.水下生產系統的設計和操作.第11部分:水下和海上用軟管系統

This part of ISO 13628 provides guidelines for the design, analysis, manufacture, testing, installation andoperation of flexible pipes and flexible pipe systems for onshore, subsea and marine applications. This part ofISO 13628 supplements ISO 13628-2 and ISO 13628-10, which specify minimum requirements for the design,material selection, manufacture, testing, marking and packaging of unbonded and bonded flexible pipe,respectively.This part of ISO 13628 applies to flexible pipe assemblies, consisting of segments of flexible pipe body withend fittings attached to both ends. Both bonded and unbonded pipe types are covered. In addition, this part ofISO 13628 applies to flexible pipe systems, including ancillary components.The applications covered by this part of ISO 13628 are sweet- and sour-service production, including exportand injection applications. This part of ISO 13628 applies to both static and dynamic flexible pipe systemsused as flowlines, risers and jumpers. This part of ISO 13628 does cover, in general terms, the use of flexiblepipes for offshore loading systems.NOTE Refer also to Reference [30] for offshore loading systems.This part of ISO 13628 does not cover flexible pipes for use in choke and kill lines or umbilical and controllines.

BS EN ISO 13628-1-2005+A1-2010石油和天然氣工業.水下采油系統的設計和操作.第1部分:一般要求和推薦規范

This part of ISO 13628 provides general requirements and overall recommendations for development ofcomplete subsea production systems, from the design phase to decommissioning and abandonment. Thispart of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with moredetailed requirements for the subsystems which typically form part of a subsea production system. However,in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) moredetailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbonsfrom one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floatingor subsea) or onshore, or to inject water/gas through subsea wells. This part of ISO 13628 and its relatedsubsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are notspecifically discussed because of their limited use. However, the information presented is applicable to thosetypes of equipment.If requirements as stated in this part of ISO 13628 are in conflict with, or are inconsistent with, requirementsas stated in the relevant complementary parts of ISO 13628, then the specific requirements in thecomplementary parts take precedence.