燃氣用手動球閥和底部密封旋塞閥檢測

燃氣用手動球閥和底部密封旋塞閥檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 16662-2008建筑給水排水設備器材術語

本標準規定了建筑給水排水設備和器材，包括衛生器具，水嘴，加壓、調節和貯存設備，加熱貯熱設備，地漏，檢查井，建筑水處理設備，游泳池、游樂池設備，冷卻設備，水景設備，雨水利用設備，管材，管件，閥門，計量、檢測儀表等方面的專用術語。本標準適用于建筑給水排水設備和器材的專用術語。

GB 50350-2015油田油氣集輸設計規范

本規范適用于陸上油田、灘海陸采油田和海上油田陸岸終端油氣集輸工程設計。

GB 50880-2013冶煉煙氣制酸工藝設計規范

本規范適用于新建、改建和擴建的冶煉煙氣制酸工程項目的工藝設計。

TSG D7002-2006壓力管道元件型式試驗細則

本規則規定的壓力管道元件型式試驗是驗證產品安全性能是否滿足安全技術要求而進行的技術文件審查、樣品檢驗測試和安全性能試驗。

CJ/T 180-2014建筑用手動燃氣閥門

本標準規定了建筑用手動燃氣閥門(以下簡稱閥門)的分類及型號,材料、結構和連接尺寸,要求,試驗方法,檢驗規則,標志、包裝、運輸和貯存。本標準適用于公稱壓力不大于1.6 MPa、公稱尺寸不大于100 mm、工作溫度不超出-20 ℃~60 ℃且其下限不低于燃氣露點溫度,安裝在建筑物內外的非直埋燃氣裝置與設施上的手動燃氣球閥和底部密封的旋塞閥。本標準所指燃氣為符合GB/T 13611規定的燃氣。

HJ 2000-2010大氣污染治理工程技術導則

本標準規定了大氣污染治理工程在設計、施工、驗收和運行維護中的通用技術要求。本標準為環境工程技術規范體系中的通用技術規范。對于已有相應的工藝技術規范或污染源技術規范的工程,應同時執行本標準和相應的工藝技術規范或污染源技術規范,對于沒有工藝技術規范或污染源技術規范的工程,應執行本標準。本標準可作為大氣污染治理工程環境影響評價、設計、施工、驗收及運行與管理的技術依據。

JB/T 4365-1997專用的潤滑、軸密封和控制油系統

　　本檔準規定了專用的潤滑油系統、軸密封油系統及控制油系統的低要求。這些系統適用于壓縮機、齒輪傳動裝置、泵及驅動機等設備，不適用于內燃機。 特殊聲明： a）當買方在訂貨單或與其有關的數據表中同意系統按JB/T 4365標準供貨時，就要優先采用本標準，不得優先采用其他標準中類同內容的任何條款。 b）如本標準與詢價書或訂貨單有抵觸時，則要以訂貨單中的資料為準。 c）附錄A給出了典型系統組件的略圖及典完整的潤滑油系統、軸密封油系統及控制油系統圖的示意圖，這些略圖示出了本標準的通常原理和要求，包括幫助買方選擇合理的系統。在訂單生效前同買方與賣方協商確定雙方均能接受的系統。 d)本標準規定了買方要確定的供貨范圍、質量水平或部件的牌號（材質）要求。系統型式、總布置圖（包括油站方位平面圖和主視圖）、油站占用空間及其他要求。 e)本標準規定了“設計”一詞，在買方技術文件中應避免使用（如設計功率、設計壓力、設計溫度或設計轉速）。此詞條只限于設備設計人員和制造廠使用。 f）本標準規定了相應的公制尺寸、賣方可以提出變更設計（7.1報價要求）。經買賣雙方協商同意，可以提供“等值的”英制的尺寸、緊固件及法蘭。

DB11/T 301-2005燃氣室內工程設計施工驗收技術規定

本規定適用于北京市居民生活、商業及工業企業生產、采暖通風和空調使用的天然氣、氣態液化\r石油氣、人工煤氣作燃料的新建、擴建、改建燃氣室內工程的設計、施工及驗收

DB11/T 302-2005燃氣輸配工程設計施工驗收技術規定

本規定適用于北京市居民生活、商業、工業企業、采暖通風和空調等用燃氣作燃料的新建、擴建\r或改建的燃氣輸配工程的設計、施工及驗收

UL 1776-2002高壓清洗機

These requirements cover inverters ,converters ,charge controllers ,and output controllers intended for use in stand-alone(not grid connected) or utility-interactive (grid-connected) power systems .Utility-interactive inverters and converters are intended to be installed in parallel with an electric supply system or an electric utility to supply common loads.

DIN EN 331-2016建筑物燃氣設備上的手動球閥和底部關閉錐形塞閥.德文版本EN 331-2015

This European standard specifies the characteristics for the construction, performance and safety of ball valves and closed bottom taper plug valves. It also details the test methods and marking provisions. It applies to metallic valves not directly buried for domestic and commercial installations inside or outside of buildings with pressures up to 5 bar, using gases of the first, second and third family (specified in EN 437).

DIN EN 746-2-2011工業熱處理設備.第2部分:燃燒和燃料處理系統的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

DIN EN 1775-2007供氣.建筑物用煤氣管道工程.大工作壓力≤5bar.功能推薦

1.1 This standard specifies general recommendations for the design, construction, testing, commissioning,operation and maintenance of installation pipework; pipework between the delivery point of the gas and the inletconnection to the gas appliance.This standard specifies common basic principles for gas installation pipework.Users of this European standard need to be aware that more detailed national standards and/or codes of practicemay exist in the CEN member countries.This standard is intended to be applied in association with these national standards and/or codes of practice settingout the above mentioned basic principles.In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with therequirements of this standard, national legislation/regulation takes precedence as illustrated in CEN/TR 13737.NOTE 1 CEN/TR 13737 contains: - clarification of relevant legislation/regulations applicable in a country; - if appropriate, more restrictive national requirements; - national contact point for the latest information.This standard applies to:-- gas installations in residential, commercial and public access building having a maximum operating pressure (MOP) less than or equal to 5 bar;-- industrial gas installations having a maximum operating pressure (MOP) less than or equal to 0,5 bar.NOTE 2 For industrial gas installations having a MOP above 0,5 bar, or installations having a MOP above 5 bar, see prEN15001-1.This standard is applicable to new installation pipework as well as to replacements of, or extensions to, existinginstallation pipework.This standard does not contain detailed recommendations relating to the laying of buried pipework. ~,~NOTE 3 For more information on buried pipework, see EN 12007-1, EN 12007-2 and EN 12007-3.NOTE 4 For more information on gas pressure regulating installations, see EN 12279.NOTE 5 For more information on gas metering systems, see EN 1776.1.2 This standard is applicable to installation pipework supplied from gas distribution systems and from liquefiedpetroleum gases (LPG) storage vessels.Excluded are:-- single appliance LPG installations without fixed pipework, achieved by a flexible appliance connector from an adjacent LPG storage cylinder.-- LPG storage vessels.1.3 In this standard the term 'gas' refers to combustible gases, which are gaseous at 15 ~C and I 013,25 mbar.These gases, odorized for safety reasons, are commonly referred to as manufactured gas, natural gas or liquefiedpetroleum gases (LPG). They are also referred to as first, second or third family gases (see EN 437). 0In this standard, all pressures are gauge pressures, unless otherwise stated.

DIN EN ISO 10414-1-2009石油和天然氣工業 鉆井液的現場試驗 第1部分:水基液

This part of ISO 10414 provides standard procedures for determining the following characteristics ofwater-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) water, oil and solids contents;e) sand content;f) methylene blue capacity;g) pH;h) alkalinity and lime content;i) chloride content;j) total hardness as calcium.Annexes A through K provide additional test methods which may be used for-- chemical analysis for calcium, magnesium, calcium sulfate, sulfide, carbonate and potassium;-- determination of shear strength;-- determination of resistivity;-- removal of air;-- drill-pipe corrosion monitoring;-- sampling, inspection and rejection;-- rig-site sampling;-- calibration and verification of glassware, thermometers, viscometers, retort-kit cup and drilling-fluid balances;-- permeability-plugging testing at high temperature and high pressure for two types of equipment;-- example of a report form for water-based drilling fluid.

BS 6739-2009過程控制系統儀表的實施規范:安裝設計和實施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 1775-2007燃氣供應.建筑物用燃氣管道.大工作壓力不超過或等于5 bar.功能性推薦規范

1.1 This standard specifies general recommendations for the design, construction, testing, commissioning,operation and maintenance of installation pipework; pipework between the delivery point of the gas and the inletconnection to the gas appliance.This standard specifies common basic principles for gas installation pipework.Users of this European standard need to be aware that more detailed national standards and/or codes of practicemay exist in the CEN member countries.This standard is intended to be applied in association with these national standards and/or codes of practice settingout the above mentioned basic principles.In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with therequirements of this standard, national legislation/regulation takes precedence as illustrated in CEN /TR 13737.NOTE 1 CEN/TR 13737 contains:- clarification of relevant legislation/regulations applicable in a country;- if appropriate, more restrictive national requirements;- national contact point for the latest information.This standard applies to:- gas installations in residential, commercial and public access building having a maximum operating pressure(MOP) less than or equal to 5 bar;- industrial gas installations having a maximum operating pressure (MOP) less than or equal to 0,5 bar.NOTE 2 For industrial gas installations having a MOP above 0,5 bar, or installations having a MOP above 5 bar, see prEN15001-1.This standard is applicable to new installation pipework as well as to replacements of, or extensions to, existinginstallation pipework.This standard does not contain detailed recommendations relating to the laying of buried pipework.NOTE 3 For more information on buried pipework, see EN 12007-1, EN 12007-2 and EN 12007-3.NOTE 4 For more information on gas pressure regulating installations, see EN 12279.NOTE 5 For more information on gas metering systems, see EN 1776.1.2 This standard is applicable to installation pipework supplied from gas distribution systems and from liquefiedpetroleum gases (LPG) storage vessels.Excluded are:- single appliance LPG installations without fixed pipework, achieved by a flexible appliance connector from anadjacent LPG storage cylinder.- LPG storage vessels.1.3 In this standard the term 'gas' refers to combustible gases, which are gaseous at 15 °C and 1 013,25 mbar.These gases, odorized for safety reasons, are commonly referred to as manufactured gas, natural gas or liquefiedpetroleum gases (LPG). They are also referred to as first, second or third family gases (see EN 437).In this standard, all pressures are gauge pressures, unless otherwise stated.