建筑接縫用密封膠檢測

建筑接縫用密封膠檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 14682-2006建筑密封材料術語

本標準規定了建筑密封材料的常用術語和定義。 本標準適用于建筑密封材料領域及相關行業。

GB/T 14683-2017硅酮和改性硅酮建筑密封膠

本標準規定了硅酮和改性硅酮建筑密封膠產品的術語和定義、分類、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于普通裝飾裝修和建筑幕墻非結構性裝配用硅酮建筑密封膠，以及建筑接縫和干縮位移接縫用改性硅酮建筑密封膠。

GB/T 22083-2008建筑密封膠分級和要求

本標準對建筑用密封膠根據其性能及應用進行分類和分級，并給出了不同級別的要求和相應試驗方法。

GB/T 34327-2017建筑幕墻術語

本標準規定了建筑幕墻的通用術語和定義。本標準適用于各種類型的建筑幕墻。

GB/T 35609-2017綠色產品評價 防水與密封材料

本標準規定了綠色建筑防水與密封材料的術語和定義、評價要求、評價方法。本標準適用于建筑防水卷材、防水涂料和密封膠的綠色產品評價。

GB 50108-2008地下工程防水技術規范

本規范適用于工業與民用建筑地下工程、防護工程、市政隧道、山嶺及水底隧道、地下鐵道、公路隧道等地下工程防水的設計和施工。

CECS 217-2006聚硫、聚氨酯密封膠給水排水工程應用技術規程

本規程適用于雙組份聚硫、雙組份聚氨酯建筑密封膠(以下簡稱聚硫、聚氨酯密封膠)防水密封工程的材料選用、施工及驗收。水利、市政、地鐵、隧道、道路、機場、建筑等工程中采用聚硫、聚氨酯密封膠防水密封時，可參照本規程執行。

JC/T 484-2006丙烯酸酯建筑密封膠

　　本標準規定了建筑接縫用丙烯酸酯密封膠的產品的分類、要求、試驗方法、檢驗規則及標志、包裝、運輸、貯存的基本要求。　　本標準適用于以丙烯酸酯乳液為基料的單組分水乳型建筑密封膠。

JC/T 881-2017混凝土接縫用建筑密封膠

本標準規定了混凝土接縫用建筑密封膠的術語和定義、分類和標記、要求、試驗方法、檢驗規則以及標志、包裝、運輸和貯存。本標準適用于混凝土接縫用建筑密封膠。

SH/T 3132-2013石油化工鋼筋混凝土水池結構設計規范

本規范規定了石油化工鋼筋混凝土水池的材料、荷載、計算及構造的要求。本規范適用于石油化工現澆鋼筋混凝土水池、非貯液池及地下式、半地下式泵房的結構設計。本規范不適用于裝配式鋼筋混凝土水池、預應力混凝土水池及沉井類結構設計。本規范不涉及水池地基處理,當需要進行地基處理時,應符合現行有關地基處理技術規范的規定。

JG/T 372-2012建筑變形縫裝置

本標準規定了建筑變形縫裝置的術語和定義、分類及代號、標記、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于變形縫寬度為6mm～500mm，伸縮量為±3mm～±250mm的建筑變形縫裝置。

JGJ 103-2008塑料門窗工程技術規程

本規程適用于未增塑聚氯乙烯（PVC-U）塑料門窗的設計、施工、驗收及保養維修。

JGJ/T 181-2009房屋建筑與市政基礎設施工程檢測分類標準

本標準適用于房屋建筑和市政基礎設施工程檢測的分類。

JGJ/T 212-2010地下工程滲漏治理技術規程

本規程適用于地下工程滲漏的治理。

JGJ/T 400-2017裝配式勁性柱混合梁框架結構技術規程

本規程適用于抗震設防烈度為6度、7度和8度地震區裝配式勁性柱混合梁框架結構工程的設計、施工及驗收。

TB 10003-2016鐵路隧道設計規范

本規范適用于高速鐵路、城際鐵路、重載鐵路和客貨共線Ⅰ、Ⅱ級鐵路標準軌距隧道設計。

ASTM C1642-2007氣溶膠泡沫填縫劑和其它建筑填縫及絕緣材料漏氣率的測定用標準實施規程

This practice is intended to measure air flow through materials used to fill joints found in building construction. This practice does not purport to establish all required criteria for the selection of an air barrier assembly. Therefore, the results should be used only for comparison purposes and should not be seen as the equivalent to field installed building systems.1.1 This practice is intended to determine the air leakage rate of aerosol foam sealants as measured in a standardized jig. This practice provides a procedure for preparing the test apparatus and further describes the application of aerosol foam sealant and other joint fillers to the apparatus prior to conducting Test Method E 283.1.2 This practice allows testing laboratories to quantify the air leakage rate of aerosol foam sealants or joint filling products using Test Method E 283 and reporting the data in L/(s m2) according to Practice E 29.1.3 This practice is used in conjunction with Test Method E 283. Although Test Method E 283 is a laboratory test method used with fenestration products, individuals interested in performing field air leakage tests on installed units should reference Test Method E 783 and AAMA 502.1.4 Aerosol foam sealants are used for a variety of end use applications generally intended to reduce air leakage in the building envelope.1.5 Insulating type materials also will be found suitable for evaluation with this practice. 1.6 There are no other known practices or test methods that specify the preparation of the assemblies used to determine the air leakage rate of gap filling sealants, dry preformed foams or insulations.1.7 The values given in SI units are the standard. The inch-pound units in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1642-2014氣溶膠泡沫填縫劑和其它建筑填縫及絕緣材料漏氣率的測定用標準實施規程

5.1x00a0;This practice is intended to measure air flow through materials used to fill joints found in building construction. 5.2x00a0;This practice does not purport to establish all required criteria for the selection of an air barrier assembly. Therefore, the results should be used only for comparison purposes and should not be seen as the equivalent to field installed building systems. 1.1x00a0;This practice is intended to determine the air leakage rate of aerosol foam sealants as measured in a standardized jig. This practice provides a procedure for preparing the test apparatus and further describes the application of aerosol foam sealant and other joint fillers to the apparatus prior to conducting Test Method E283. 1.2x00a0;This practice allows testing laboratories to quantify the air leakage rate of aerosol foam sealants or joint filling products using Test Method E283 and reporting the data in L/(s8201;x00b7;8201;m2) according to Practice E29. 1.3x00a0;This practice is used in conjunction with Test Method E283. Although Test Method E283 is a laboratory test method used with fenestration products, individuals interested in performing field air leakage tests on installed units should reference Test Method E783 and AAMA 502. 1.4x00a0;Aerosol foam sealants are used for a variety of end use applications generally intended to reduce air leakage in the building envelope. 1.5x00a0;Insulating type materials also will be found suitable for evaluation with this practice. 1.6x00a0;There are no other known practices or test methods that specify the preparation of the assemblies used to determine the air leakage rate of gap filling sealants, dry preformed foams or insulations. 1.7x00a0;The values given in SI units are the standard. The inch-pound units in parentheses are for information only. 1.8x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.