船用高壓手動球閥檢測

船用高壓手動球閥檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 51156-2015液化天然氣接收站工程設計規范

本規范適用于陸上新建、擴建和改建的液化天然氣接收站工程的設計。

HG/T 20507-2014自動化儀表選型設計規范

本規范適用于化工行業新建、擴建和改造項目中的自動化儀表選型設計。

HG/T 21608-2012液體裝卸臂工程技術要求

本標準適用于公稱壓力CL150、CL300或PN2.5、PN6、PN10、PN16、PN25、PN40、PN63，設計溫度-196℃～250℃范圍內，通過液體裝卸臂實現汽車槽車、火車槽車或槽船裝卸各種石油化工液體介質。

CB/T 3191-2013船用高壓手動球閥

本標準規定了船用高壓手動球閥(以下簡稱球閥)的分類和標記、要求、試驗方法、檢驗規則、標志與包裝。本標準適用于工作壓力為6.4 MPa~32 MPa,介質為空氣、二氧化碳及液壓油等管路系統用球閥的設計、制造和驗收。

CB/T 3495.16-1997船舶工業檔案管理規則.著錄標引細則和主題詞表

本標準規定了船舶工業檔案著錄標引的細則及著錄標引用的漢語主題詞表。 本標準適用于船舶工業檔案的著錄標引工作。

CB 4288-2013船廠起重設備安全技術要求

本標準規定了船舶行業各企業用起重設備的安全技術要求。本標準適用于門座起重機、門式起重機、橋式起重機、浮式起重機、汽車起重機、塔式起重機、降機、卷揚機等起重機械的日常檢查工作。也適用于自制、改造的起重設備的日常檢查工作。其他類型起重設備可參照執行。

CB/Z 800-2004船用閥門選用指南

本指導性技術文件給出了船舶動力管路和船舶系統管路中閥門的功能、使用方法、在各管路系統中的選用、安裝方法等的指南。\t本指導性技術文件適用于船舶動力管路和船舶系統管路中閥門的選用。

JB/T 3750-1984產品類種劃分

本標準適用于機械工業部所生產的產品。作為計劃、統計管理工作的產品類中劃分的統一依據。 本標準不包括大型成套設備。

JB/T 9236-2014工業自動化儀表產品型號編制原則

本標準規定了工業自動化儀表產品(以下簡稱產品)型號的編制原則。本標準適用于編制產品的型號。本標準不適用于DDZ-S系列儀表、KF系列氣動基地式儀表和工業控制計算機系統,它們的型號編制原則另行規定。

EN ISO 13628-1-2005石油和天然氣工業.水下采油系統的設計和操作.第1部分:一般要求和建議 ISO 13628-1-2005

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment.This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells.This part of ISO 13628 and its related subsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.If requirements as stated inThis part of ISO 13628 are in conflict with, or are inconsistent with, requirements as stated in the relevant complementary parts of ISO 13628, then the specific requirements in the complementary parts take precedence.

DIN EN ISO 13628-7-2007石油和天然氣工業.水下采油系統的設計和操作.第7部分:完井/修井提升管系統

This standard gives requirements and recommendations for the design, analysis, materials, fabrication testing and operation of subsea completion/workover (C/WO) riser systems run from a floating vessel.#,,#

BS EN ISO 13628-1-2005+A1-2010石油和天然氣工業.水下采油系統的設計和操作.第1部分:一般要求和推薦規范

This part of ISO 13628 provides general requirements and overall recommendations for development ofcomplete subsea production systems, from the design phase to decommissioning and abandonment. Thispart of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with moredetailed requirements for the subsystems which typically form part of a subsea production system. However,in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) moredetailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbonsfrom one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floatingor subsea) or onshore, or to inject water/gas through subsea wells. This part of ISO 13628 and its relatedsubsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are notspecifically discussed because of their limited use. However, the information presented is applicable to thosetypes of equipment.If requirements as stated in this part of ISO 13628 are in conflict with, or are inconsistent with, requirementsas stated in the relevant complementary parts of ISO 13628, then the specific requirements in thecomplementary parts take precedence.