金屬移動腳手架檢測

金屬移動腳手架檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 24957-2010冷凍輕烴流體 船上膜式儲罐和獨立棱柱形儲罐的校準 物理測量法

本標準規定了用于運輸冷凍輕烴流體的船上膜式儲罐和獨立棱柱形儲罐的內部測量方法。除實際的測量過程外，還規定了用于貨物數量計量的校準表和修正表編制的計算程序。對于膜式儲罐，本標準的程序是利用安裝膜使用的腳手架來支承測量設備，而對于獨立棱柱形儲罐，應使用其他的安全方式進入到要求測量的位置。

GB 26164.1-2010電業安全工作規程.第1部分：熱力和機械

本部分規定了從事電力生產的熱力和機械作業的人員在生產現場或工作中的基本安全工作要求。本部分適用于從事電力生產的所有人員和進入電力生產現場的有關人員。

GB/T 50214-2013組合鋼模板技術規范

本規范適用于工業與民用建筑及一般構筑物的現澆混凝土工程和預制混凝土構件所用的組合鋼模板的設計、制作、施工和驗收。

GB 51221-2017城鎮污水處理廠工程施工規范

本規范適用于新建、擴建和改建的城鎮污水處理廠工程施工。

SH/T 3555-2014石油化工工程鋼腳手架搭設安全技術規范

本規范規定了鋼腳手架的材料與構配件、通用腳手架結構形式和構造的要求;規定了腳手架結構設計、腳手架的計算、腳手架搭設的施工與管理的要求。本規范適用于石油化工、煤化工、天然氣化工等工程建設鋼腳手架搭設的結構設計、施工、驗收與使用過程的管理。

JGJ/T 275-2013密肋復合板結構技術規程

本規程適用于8層及8層以下且房屋高度不超過24m的多層密肋復合板結構及9層及9層以上或房屋高度超過24m的高層密肋復合板結構。非抗震設計和抗震設防烈度為6度至8度抗震設計的密肋復合板結構,其適用的房屋大高度應符合本規程的有關規定。本規程不適用于建造在危險地段以及發震斷裂小避讓距離內的密肋復合板結構。

JGJ/T 414-2018建筑施工模板和腳手架試驗標準

本標準適用于建筑工程和市政工程用模板、支撐架和腳手架的檢驗及試驗。

JGJ/T 416-2017建筑用真空絕熱板應用技術規程

本規程適用于民用建筑中采用建筑用真空絕熱板的建筑節能工程的設計、施工及驗收。

DB64/ 558-2009建筑工人安全操作規程

本標準規定了建筑工人安全操作的術語和定義、總則、一般規定、架子工、瓦工、抹灰工、石工、木工、鋼筋工、混凝土工、普通工、電工、安裝電工、防水工、起重吊裝工、金屬焊割作業工、油漆工、測量工、機械設備維修工、水暖工、鉚工、通風工、筑爐工、保溫工、樁基施工、大模片施工、鋼結構及網架施工、裝飾裝修施工、拆除施工、土方及筑路機械、樁工機械、吊裝及垂直運輸機械、混凝土機械、中小型施工機具、市政工程的操作。

DIN-Fachbericht 151-2007技術產品文件.設備管理文件.建筑物文件

The standard describes the extent and the content of the documentation which is handed over when a building is transitioned from the constructionphase to the usingphase.

BS PD CEN/TR 13833-2003施工企業的資格鑒定

This European Standard specifies the definitions, procedures, criteria and their assessment as well as therespective documentation related to a system of qualification of construction enterprises.

ANSI Z245.41-2008廢棄物和可回收材料用設備技術和操作.混合的可回收材料的處理設備.安全要求

This American National Standard is applicable to all persons who design, manufacture, assemble, modify,operate, clean, maintain, service, or repair material recovery facilities (MRFs) which engage in receiving,storing, and processing commingled recyclable materials which have been previously collected orotherwise diverted from the solid waste stream. This standard does not apply to scrap processingfacilities (North American Industry Classification system code number 42193, formerly Standard IndustrialClassification number 5093), unless the scrap processing facility operates a MRF, which MRF would thenbe subject to this standard.The safety requirements are divided into 7 sections and are applicable as described in 1.1.1 through1.1.3.1.1.1 Sections 1 through 3 provide general information and definitions and shall apply to all materialrecovery facilities (MRFs) covered by this standard.1.1.2 Sections 4 through 6 provide for physical plant, processing machinery and mobile equipmentrequirements that shall apply to both new and existing MRFs.1.1.3 Section 7 provides for safety programs and safety requirements that shall apply to both new andexisting MRFs.

ANSI/ASSE A10.8-2011腳手架安全要求

This standard establishes safety requirements for the construction, operation, maintenance, and use of scaffolds used in the construction, alteration, demolition, and maintenance of buildings and structures. This standard does not cover permanently installed suspended scaffold systems or aerial platforms. Please note that this standard is based on the 2001 version of the A10.8 Standard, which was administratively withdrawn by ANSI. Since the standard was withdrawn it is viewed/processed as a new standard, but the new document is based on the 2001 administratively withdrawn standard.