熱電偶用陶瓷絕緣管檢測

熱電偶用陶瓷絕緣管檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 9316-2007攝影用電子閃光裝置安全要求

1.1 本標準給出了電子閃光裝置的安全要求。 1.2 本標準適用于儲能不超過2000J的不被水滴或水濺的下列攝影用電子閃光裝置及其相關裝置： a）單個閃光裝置，可有一個以上可同時閃亮的閃光頭。 b）連續多次曝光攝影用閃光裝置。 c）與攝影用電子閃光裝置連接的電池充電器和電源裝置；它可能是電源插頭的一部分。 d）附屬裝置，例如：說明書中列舉的光量調節器及閃光同步器等。 本標準不適用于頻閃裝置。 就電源而言，適用于下列幾種類型： a）用電網電源工作的閃光裝置； b）用電池工作的閃光裝置； c）電網電源和電池均可用的閃光裝置。 1.3 本標準不適用于對地額定電源電壓超過250V（有效值）的裝置。 1.4 本標準僅涉及閃光裝置的安全不涉及其他性能（見第3章）。

GB/T 9978.1-2008建筑構件耐火試驗方法.第1部分:通用要求

GB/T的本部分規定了各種結構構件在標準受火條件下確定其耐火性能的試驗方法。

GB/T 18036-2008鉑銠熱電偶細絲的熱電動勢測量方法

本標準規定了用熔絲法和比較法測量鉑銠熱電偶絲熱電動勢的方法。本標準適用于測量直徑為0.05mm～0.1mm范圍內的鉑銠熱電偶細絲。其他貴金屬和賤金屬熱電偶細絲的熱電動勢測量也可參照進行。

GB 19510.1-2009燈的控制裝置 第1部分:一般要求和安全要求

本部分規定了使用250V以下直流電或50H<下標z>或60H<下標z>的1000V以下交流電的燈的控制裝置的一般要求和安全要求。本部分還適用于尚未標準化的燈所使用的控制裝置。本部分涉及的試驗均為型式試驗。

GB/T 30429-2013工業熱電偶

本標準規定了工業熱電偶的分類、技術要求、試驗方法、檢驗規則、包裝和標志。本標準適用于分度表和允差符合GB/T 16839.1和GB/T 16839.2的可拆卸的、主要用于氧化氣氛的工業熱電偶。對于其他型式的工業熱電偶,可參照采用本標準的全部或部分條文。

GB 51037-2014微組裝生產線工藝設備安裝工程施工及驗收規范

本規范適用于新建、改建及擴建的微組裝生產線工藝設備的安裝工程施工、調試、試運行及驗收。

GB 51145-2015煤礦電氣設備安裝工程施工與驗收規范

本規范適用于煤礦建設電氣設備安裝工程的施工及驗收。

JJF 1184-2007熱電偶檢定爐溫度場測試技術規范

本規范適用于（300～1500）℃范圍內包括帶溫控器和不帶溫控器的臥式管式熱電 偶檢定爐（以下簡稱檢定爐）溫度場的測試。對于立式管式檢定爐、退火爐的溫度場測試，可參照本規范執行。

JB/T 7494-1994儀器儀表材料產品分類

本標準規定了引用標準、分類規則、產品分類。 本標準適用于儀器儀表材料產品，可作為計劃、統計、管理、標準制訂的依據。

UL 17-2008燃油器具用通風或煙囪連接件調節器

The dodument cover requirements for electrically operated damper assemblies, that are intended for installation in the vent or chimney connector of automatically operated oil-fired appliances employing an atomizing type oil burner. The damper assembly is intended to restrict or block the connector opening when the burner is not firing. These requirements cover automatic vent or chimney connector dampers for oil-fired appliances having a flue gas temperature not in excess of 538 ?C (1000 ?F), unless marked for a lower temperature. The vent or chimney connector dampers covered under these requirements are not for use on oil-fired appliances that employ vaporizing type oil burners. Automatic vent or chimney connector dampers are intended for installation in accordance with the following standards of the National Fire Protection Association: a) Oil-Burning Equipment, NFPA 31. b) Chimneys, Fireplaces, and Vents, NFPA 211. c) National Electrical Code, ANSI/NFPA 70. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL 38-2008火災報警系統用手動信令盒

1.1 These requirements cover manual signaling boxes for fire alarm systems intended for permanentinstallation and used in ordinary locations in accordance with the National Electrical Code, NFPA 70, and the National Fire Alarm Code, NFPA 72.1.2 A manual signaling box is an assembly of a mechanism having electrical contacts designed totransmit a signal when an integral part is operated manually. The signaling contacts are intended to beconnected to circuits of fire alarm systems. The types of boxes covered by these requirements are coded boxes and non-coded boxes, including signaling boxes, fire and guard’s tour reporting stations, and guard’s tour reporting stations for suppressed-signal tour combinations.1.3 A manual signaling box having a pre-wound signaling mechanism and equipped with a trippingelectromagnet to permit automatic actuation by separate detectors, and similar combination devices, shall be evaluated with regard to compliance with the applicable requirements for both manual signaling boxes and electrically-actuated transmitters.1.4 A manual signaling box shall be constructed for use with system-control units, electrically-actuatedtransmitters, or similar units that will permit its application in compliance with applicable codes andstandards of the National Fire Protection Association.1.5 These requirements do not cover electrically-actuated transmitters.

UL 296-2003燃油爐

These revisions are to the UL 296 proposals announced in the March 18, 2005 issue of ANSI's \"Standards Action.

UL 346-2005防火信號系統用水流量指示器

1.1 These requirements cover vane type waterflow indicators intended for use in fire protective signaling systems to be employed in ordinary indoor locations, in accordance with the National Fire Alarm Code, NFPA 72. 1.2 Waterflow indicators covered by these requirements include sizes 3/4 inch and larger. The indicator sizes refer to the nominal inside diameter of the main sprinkler pipe or tubing on which they are installed. 1.3 A vane type waterflow indicator is an assembly of a mechanism having electrical contacts arranged to transmit a coded or noncoded signal when the vane, located in the supply pipe (riser) of a sprinkler system, is moved by the flow of water in the pipe. This flow is normally caused by the opening of one or more sprinkler heads resulting from a fire condition. The signaling contacts are intended to be connected to circuits of private fire protective signaling systems. 1.4 These requirements do not cover pressure-operated waterflow indicators.