聚丙烯管(PP)—PP-H、PP-B、PP-R 、PP-RCT檢測

聚丙烯管(PP)—PP-H、PP-B、PP-R 、PP-RCT檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 18742.1-2017冷熱水用聚丙烯管道系統 第1部分:總則

GB/T 18742的本部分規定了冷熱水用聚丙烯管道系統的術語和定義、符號、代號和縮略語、使用條件級別、材料要求和衛生要求。本部分與GB/T 18742.2、GB/T 18742.3一起適用于建筑物內冷熱水管道系統，包括飲用水和采暖管道系統等。本部分不適用于滅火系統。

GB/T 18742.2-2017冷熱水用聚丙烯管道系統 第2部分:管材

GB/T 18742的本部分規定了以聚丙烯混配料為原料，經擠出成型的圓形橫截面的聚丙烯管材(以下簡稱管材)的定義、符號和縮略語、材料、產品分類、管系列S值的選擇、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。本部分與GB/T 18742.1、GB/T 18742.3一起適用于建筑物內冷熱水管道系統，包括飲用水和采暖管道系統等。本部分不適用于滅火系統。

GB/T 18742.3-2017冷熱水用聚丙烯管道系統 第3部分:管件

GB/T 18742的本部分規定了以聚丙烯混配料為原料，經注射成型的聚丙烯管件(以下簡稱管件)的定義、符號和縮略語、材料、產品分類、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。本部分與GB/T 18742.1、GB/T 18742.2一起適用于建筑物內冷熱水管道系統，包括飲用水和采暖管道系統等。本部分不適用于滅火系統。

CECS 414-2015復合β晶型無規共聚聚丙烯(NFPP-RCT)管道工程技術規程

本規程適用于新建、改建、擴建的以水為輸送介質的復合β晶型無規共聚聚丙烯(NFPP-RCT)管道工程的設計、施工及驗收，且管道不得用于建筑室內消防給水系統。

CJ/T 159-2015鋁塑復合壓力管(對接焊)

本標準規定了鋁塑復合壓力管（對接焊）的術語和定義、符號和縮略語、分類與標記、材料、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于輸送流體（冷水、熱水的飲用水輸配系統和給水輸配系統；采暖系統、燃氣等）的鋁塑復合壓力管。

ISO 9854-2-2023

This document specifies the values or options chosen for the test parameters (i.e. the impact energy, specimen dimensions, specimen type, specimen supports and test temperature) for both unnotched and notched specimens, for testing the impact resistance (pendulum method) of thermoplastics pipes of the following materials, in accordance with ISO 9854-1. It applies to pipes made of unplasticized poly(vinyl chloride) (PVC-U), high-impact poly(vinyl chloride) (PVC-HI), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile/butadiene/styrene (ABS), acrylonitrile/styrene/acrylate (ASA), propylene homopolymer (PP-H), propylene impact polymer (PP-B), propylene random copolymer (PP-R), propylene random copolymer with modified crystallinity (PP-RCT), and polyethylene (PE).

PPI TN-56-2018在IC級和非IC級嵌入式照明燈具附近安裝塑料壓力管道材料

INTRODUCTION This Technical Note will provide guidance about the recommended proximity of certain types of plastic pressure pipe and tubing to various types of recessed lighting fixtures, which are also known as “pot lights” or “can lights”. Recessed light fixtures are available in two classes, non-insulation contact and insulation contact (i.e. IC-rated). This Technical Note applies to the following types of plastic pressure pipes and tubing: ? CPVC: Chlorinated polyvinyl chloride ? PEX: Crosslinked polyethylene ? PE-RT: Polyethylene of raised temperature ? PP-R: Random copolymerized polypropylene ? PP-RCT: Polypropylene random copolymer with modified crystallinity & temperature resistance These materials are commonly used in applications such as hot- and cold-water plumbing, fire protection, and hydronic heating and cooling, including radiant heating and cooling systems. The information within this document

PPI TN-65-2021

INTRODUCTION Plastic pressure pipe materials are commonly used in applications such as hot- and cold-water plumbing, fire protection, and hydronic heating and cooling including radiant distribution systems. This Technical Note provides guidance about insulating the following types of plastic pressure pipe and tubing materials within residential buildings: ? CPVC: chlorinated polyvinyl chloride ? PEX: crosslinked polyethylene ? PEX/AL/PEX: crosslinked polyethylene/aluminum/crosslinked polyethylene ? PE-RT: polyethylene of raised temperature resistance ? PP-R: random copolymerized polypropylene ? PP-RCT: polypropylene random copolymer with modified crystallinity & temperature resistance This document focuses on insulating plastic pressure piping materials from the perspective of freeze protection, and not energy conservation. Requirements and

PPI TN-67-2023

INTRODUCTION This PPI Technical Note focuses on the application of chlorine dioxide within buildings and its potential effects on the following plastic hot- and cold-water plumbing distribution pipe materials: ? CPVC: chlorinated polyvinyl chloride ? PEX: crosslinked polyethylene ? PE-RT: polyethylene of raised temperature resistance ? PP-R: polypropylene random copolymer ? PP-RCT: polypropylene random copolymer with modified crystallinity & temperature resistance Currently, limited North American industry data is publicly available to predict the impact that chlorine dioxide may have on specific plumbing distribution pipe materials. This Technical Note addresses this topic based on data that has been collected through an extensive analysis of published research combined with the experience and expertise of PPI members.

T/CECS 524-2018結晶改善型無規共聚聚丙烯(PP-RCT)管道工程技術規程

本規程適用于新建、改建、擴建的以水為輸送介質的結晶改善型無規共聚聚丙烯(PP-RCT)管道工程的設計、施工及驗收。

GSO ISO 3213-2015聚丙烯（PP）管——時間和溫度對預期強度的影響

This International Standard specifies the minimum values for expected strength as a function of time and temperature in the form of reference lines, for use in calculations on pipes made of: — polypropylene homopolymer (PP-H); — polypropylene block copolymer 1) (PP-B); — polypropylene random copolymer (PP-R); — polypropylene random copolymer 2) with a modified crystallinity (PP-RCT).

DIN 1988-200-2012飲水裝置實用規程. 第200部分: 安裝類型A(封閉系統). 計劃, 部件, 器械, 材料; DVGW實用規程

This draft standard describes the code of practice for planning and construction of drinking water systems in houses and properties as well as the components, apparatus and materials which are to use. It supplements DIN EN 806-2 and gives additional specifications considering national laws, regulations and German Technical Rules.

DIN 4060-2016帶彈性密封件的下水道和污水管用接頭.對彈性密封件的接頭的要求和試驗

This Standard is applicable in combination with DIN EN 681-1, DIN EN 681-2 and DIN EN 681-3 for joints for pipe connections of sewers and drains as well as manholes and sanitary appliances and connections with elastomeric seals. The requirements of the document are only applicable, if the corresponding product-standard for pipes of sewers and drains as well as manholes and sanitary appliances and connections with elastomeric seals doesn't contain such requirements. I does not apply to joints for pipes for which functional test methods are published in European Standards for pipes and fittings.

DIN 4102-4-2016建筑材料和建筑構件的耐火性能.概要和分級的建筑材料、構件和特種構件的應用

This document contains catagorized results of fire tests of buildings materials, components and construction types. Due to the assignment to the classes of building materials according to DIN 4102 part 1 and the fire resistance classes of the other parts of DIN 4102 respectively, further fire tests for the verification of usability required by the building regulations are not necessary.

DIN 4266-1-2011垃圾填埋地用排污管.第1部分:PE和PP制成的排污管

The draft standard specifies requirements and test methods for perforated pipes made from polyehtylene (PE) and polypropylene (PP) applied for collection and drainage of seepage water for landfills.