混凝土砌塊和磚塊檢測

混凝土砌塊和磚塊檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 50702-2011砌體結構加固設計規范

為了使砌體結構的加固做到技術可靠、安全適用、經濟合理、確保質量，制定本規范。本規范適用于房屋和一般構筑物砌體結構的加固設計。 砌體結構加固前，應根據不同建筑類型分別按現行標準《工業建筑可靠性鑒定標準》GB 50144和《民用建筑可靠 性鑒定標準》GB 50292等標準的有關規定進行可靠性鑒定。當與抗震加固結合進行時，尚應按現行標準《建筑抗震鑒定標準》GB 50023的有關規定進行抗震能力鑒定。 砌體結構的加固設計除應符合本規范的規定外，尚應符合現行有關標準的規定。

GB/T 50743-2012工程施工廢棄物再生利用技術規范

本規范適用于建設工程施工過程中廢棄物的管理、處理和再生利用；不適用于已被污染或腐蝕的工程施工廢棄物再生利用。

GB 50924-2014砌體結構工程施工規范

本規范適用于建筑工程的磚、石、砌塊等砌體結構工程的施工。

CECS 257-2009混凝土磚建筑技術規范

本規范適用于非抗震設防區和抗震設防烈度為8度及8度以下的地區，以混凝土磚為墻體材料的一般工業與民用建筑的設計、施工及驗收。

CJJ 36-2016城鎮道路養護技術規范

本規范適用于竣工驗收后交付使用的城鎮道路(包括車行道、人行道、停車場、廣場及附屬設施)的養護。

JG/T 505-2016建筑垃圾再生骨料實心磚

本標準規定了建筑垃圾再生骨料實心磚的術語和定義、分類與標記、原材料、要求、試驗方法、檢驗規則、養護、標志、包裝、運輸和貯存。本標準適用于以建筑垃圾再生骨料為主要原料、水泥等為膠凝材料制成的非燒結實心磚。

JGJ/T 101-2015建筑抗震試驗規程

本規程適用于建筑物、構筑物及其構件的抗震性能試驗。

JGJ/T 371-2016非燒結磚砌體現場檢測技術規程

本規程適用于非燒結磚砌體中砌體抗壓強度、砌體抗剪強度、砌筑砂漿強度和砌筑塊材強度的現場檢測及強度推定。本規程中砌筑砂漿及塊材的各種檢測方法，均不適用于遭受高溫、長期浸水、火災、侵蝕環境等條件下的強度檢測。

ASTM C216-2007a飾面磚(粘土或頁巖制實心砌塊)的標準規范

1.1 This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure.1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section ) of this specification is beyond the scope of this specification.1.3 The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C 902).1.4 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see firing, fired bond, and incipient fusion in Terminology C 43).1.5 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.6 Three types of brick in each of two grades are covered.1.7 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

ASTM C216-2014飾面磚(粘土或頁巖制實心砌塊)標準規格

1.1x00a0;This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. 1.2x00a0;The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 7) of this specification is beyond the scope of this specification. 1.3x00a0;The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C902). 1.4x00a0;Brick are ceramic products manufactured primarily from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). Additives or recycled materials are permitted to be included at the option of the manufacturer. The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see Terminology C1232). 1.5x00a0;Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5.1x00a0;This standard and its individual requirements shall not be used to qualify or corroborate the performance of a masonry unit made from other materials, or made with other forming methods, or other means of binding the materials. 1.6x00a0;Three types of brick in each of two grades are covered. 1.7x00a0;The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.8x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM C1790-2014粉煤灰飾面磚的標準規格

1.1x00a0;This specification covers fly ash brick intended for use in masonry, which are made from fly ash, water, and suitable mineral aggregates with or without the inclusion of other materials, and without the use of portland cement. This specification covers units intended for use in masonry, in both structural and facing applications. 1.2x00a0;Units covered under this specification include a fly ash binder that undergoes hydraulic, pozzolanic, alkali-activated, or geopolymer reactions, or any combination thereof. These chemical reactions, in conjunction with the other materials in the units, provide the strength and durability necessary to meet the requirements of this specification. Note 1:x00a0;This specification addresses properties of units formed using fly ash, aggregates, and other allowed binders. Although not required by this standard, users may request tests that establish assembly performance such as unit-mortar bond and fire resistance. As an alternative to tests, evidence of successful use in similar applications could be provided to establish assembly performance. 1.3x00a0;This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4x00a0;The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1790-2014a飛灰貼面磚的標準規格

1.1x00a0;This specification covers fly ash brick intended for use in masonry, which are made from fly ash, water, and suitable mineral aggregates with or without the inclusion of other materials, and without the use of portland cement. This specification covers units intended for use in masonry, in both structural and facing applications. 1.2x00a0;Units covered under this specification include a fly ash binder that undergoes hydraulic, pozzolanic, alkali-activated, or geopolymer reactions, or any combination thereof. These chemical reactions, in conjunction with the other materials in the units, provide the strength and durability necessary to meet the requirements of this specification. Note 1:x00a0;This specification addresses properties of units formed using fly ash, aggregates, and other allowed binders. Although not required by this standard, users may request tests that establish assembly performance such as unit-mortar bond and fire resistance. As an alternative to tests, evidence of successful use in similar applications could be provided to establish assembly performance. 1.3x00a0;This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4x00a0;The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1790-2015飛灰貼面磚的標準規格

1.1x00a0;This specification covers fly ash brick intended for use in masonry, which are made from fly ash, water, and suitable mineral aggregates with or without the inclusion of other materials, and without the use of portland cement. This specification covers units intended for use in masonry, in both structural and facing applications. 1.2x00a0;Units covered under this specification include a fly ash binder that undergoes hydraulic, pozzolanic, alkali-activated, or geopolymer reactions, or any combination thereof. These chemical reactions, in conjunction with the other materials in the units, provide the strength and durability necessary to meet the requirements of this specification. Note 1:x00a0;This specification addresses properties of units formed using fly ash, aggregates, and other allowed binders. Although not required by this standard, users may request tests that establish assembly performance such as unit-mortar bond and fire resistance. 1.3x00a0;This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4x00a0;The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

EN 15287-1-2007煙囪.煙囪的設計,安裝和試用.第1部分:非密封房間加熱器具用煙囪［代替:CEN EN 12391-1］

This European Standard describes the method of specifying the design, installation criteria for system chimneys, construction of custom built chimneys, and the relining of existing chimneys. It also gives information on commissioning of chimneys.This European Standard also deals with connecting flue pipes.This European Standard does not apply to freestanding chimneys covered by EN 13084-1.This European Standard excludes chimneys designated H (high positive pressure chimneys) and chimneys for room-sealed heating appliances. For the purpose of this European Standard the term \"installation\" includes construction.

NF P10-204-1-1-2008建筑工程.小型磚石隔墻.第1-1部分:技術模型條款的合同單

Le présent document définit les clauses techniques d'exécution d'ouvrages courants de cloisons de petits éléments de ma?onnerie hourdés au mortier d'usage courant, au mortier-colle pour joints minces ou au platre.Les dites cloisons ont une épaisseur inférieure ou égale à 15 cm.Les ouvrages concernés sont les cloisons de distribution, les cloisons séparatives non porteuses, les parois de gaines techniques et les cloisons de doublage de batiments destinés aux logements, batiments scolaires et hospitaliers et aux immeubles de bureaux, pour des conditions normales d'utilisation, c'est-à-dire occupés en permanence et sans surpeuplement.Pour certains ouvrages autres que courants dont les exigences peuvent être différentes (batiments à usage industriel, agricole, garages), les prescriptions peuvent être adaptées en tenant compte des caractéristiques particulières des constructions et de leur destination, fonction du programme arrêté par le ma?tre d'ouvrage, précisé dans les Documents Particuliers du Marché.Le présent document ne s'applique donc pas aux murs de remplissage extérieurs ni aux murs participant à la stabilité de la structure qui sont traités par la norme NF DTU 20.1.

NF P15-201-1-1-2008建筑工程.用灰漿制成的抹灰工程.第1-1部分:技術模型條款的合同單

Le présent document définit les règles de préparation et d'exécution des enduits épais en mortier de ciments, de chaux hydrauliques, de chaux aérienne, de mélange platre et chaux aérienne, appliqués sur les supports suivants :- ma?onneries neuves ou anciennes de pierres, briques de terre cuite, blocs en béton, montés au mortier de liants hydrauliques ;- bétons courants ou soignés, béton caverneux, bétons de granulats légers ;- ma?onneries de blocs en béton cellulaire autoclavé ;- lattis métalliques ;- ma?onneries en moellons, à pierres vues.- ma?onneries anciennes montées aux mortiers peu résistants ou de platre, sauf les enduits sur les monuments historiques, sur les édifices implantés dans les sites faisant l'objet d'une protection patrimoniale au titre du code du patrimoine, du code de l'urbanisme ou du code de l'environnement et sur les batiments anciens patrimoniaux.Ce document s'applique aux enduits extérieurs et intérieurs verticaux à fonctions d'imperméabilisation et de parement et aux enduits intérieurs verticaux avec ou sans fonction d'imperméabilisation ainsi qu'aux enduits horizontaux extérieurs ou intérieurs exécutés en sous-face d'ouvrages de tous batiments et ouvrages connexes.Il s'applique également aux enduits de dressement.Il ne traite pas des enduits minces de ragréage ou de lissage (épaisseur inférieur ou égal à 5 mm).Il ne s'applique pas aux enduits à fonctions particulières : enduits d'étanchéité, enduits de cuvelage qui font l'objet de normes NF DTU ou recommandations spécifiques.

DIN 4102-4-2016建筑材料和建筑構件的耐火性能.概要和分級的建筑材料、構件和特種構件的應用

This document contains catagorized results of fire tests of buildings materials, components and construction types. Due to the assignment to the classes of building materials according to DIN 4102 part 1 and the fire resistance classes of the other parts of DIN 4102 respectively, further fire tests for the verification of usability required by the building regulations are not necessary.

DIN 4109-32-2016建筑物隔聲. 第32部分: 隔聲驗證使用數據 (組件目錄). 實心結構

This standard contains acoustic data for elements and designs for solid structures intended for use in the methods of calculation that are specified in DIN 4109-2 and are used in the verifications according to DIN 4109-1, without conducting acoustic suitability tests.