聲納用水密連接器檢測

聲納用水密連接器檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

CB/T 4387-2013聲納用水密連接器

本標準規定了聲納用水密連接器(以下簡稱水密連接器)的分類與型號規格、要求、試驗方法、驗規則、標志、包裝、運輸和貯存。本標準適用于聲納用水密連接器的設計、生產、試驗和驗收,其他用途水密連接器可參照使用。

HB 8305-2012GDM系列水密封光電連接器規范

本規范規定了GDM系列水密封光電連接器(以下簡稱連接器)的要求、質量保證規定和交貨準備等。本規范適用于連接器的設計、制造和驗收。

HB 8309-2012SM系列水密封電連接器規范

本規范規定了SM系列水密封電連接器(以下簡稱連接器)的要求、質量保證規定和交貨準備等。本規范適用于連接器的設計、制造、檢驗等。

EN ISO 13628-5-2009石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

EN ISO 19901-6-2009石油和天然氣工業.海上建筑物的詳細要求.第6部分:船舶管理

This part of ISO 19901 provides requirements and guidance for the planning and engineering of marine operations, encompassing the design and analysis of the components, systems, equipment and procedures required to perform marine operations, as well as the methods or procedures developed to carry them out safely.

DIN EN ISO 13628-5-2010石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

DIN EN ISO 19901-6-2012石油和天然氣工業.海上建筑物的詳細要求.第6部分:船舶管理

This part of ISO 19901 contains metocean design and operating considerations for offshore structures.

BS EN ISO 13628-5-2009石油和天然氣工業.水下采油系統設計和操作.水下臍帶管

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.

BS EN ISO 19901-6-2009石油和天然氣工業.海上建筑物的具體要求.船舶管理

This part of ISO 19901 provides requirements and guidance for the planning and engineering of marineoperations, encompassing the design and analysis of the components, systems, equipment and proceduresrequired to perform marine operations, as well as the methods or procedures developed to carry them out safely.This part of ISO 19901 is applicable to marine operations for offshore structures including- steel and concrete gravity base structures (GBS);- piled steel structures and compliant towers;- tension leg platforms (TLP);- deep draught floaters (DDF), including spars or deep draught caisson vessels (DDCV);- floating production semi-submersibles (FPSS);- floating production, storage and offloading vessels (FPSO);- other types of floating production systems (FPS);- mobile offshore units (MOU);- topsides and components of any of the above;- subsea templates and similar structures;- gravity, piled, drag embedded and suction or other anchors;- tendon foundations;- associated mooring systems.This document is also applicable to modifications of existing structures, e.g. installation of additional topsides modules.This part of ISO 19901 is not applicable to the following marine operations:a) construction activities, e.g. in a fabrication yard onshore, where there is no exposure to the marine environment;b) drilling, processing and petrochemical activities;c) routine marine activities during the service life of the structure;d) drilling from mobile offshore drilling units (MODU);e) installation of pipelines, flowlines, risers and umbilicals;f) diving.