電纜電纜及其原材料檢測

電纜電纜及其原材料檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

CJJ 167-2012城市軌道交通直線電機牽引系統設計規范

本規范適用于采用直線電機非粘著驅動、車輛裝設短定子、軌道中部設置感應板、鋼輪/鋼軌作為支撐和導向、列車高速度為100km/h的新建城市軌道交通直線電機牽引系統工程的設計。

SJ 30030.10-2018宇航級和高可靠電連接器工藝控制要求 第10部分:組件端接

本部分規定了宇航級和高可靠電連接器(以下簡稱宇高電連接器)組件端接工藝控制中人員、設備、材料、工藝過程、生產環境、禁限用工藝控制及檢驗要求等內容。本部分適用于宇高電連接器組件端接工藝過程的控制與檢驗。

EN ISO 13628-5-2009石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

DIN EN 4056-001-2015航空航天系列.導線電纜扎匝.第001部分:技術規范;德文和英文版本EN 4056-001-2015

This European Standard specifies the characteristics, test methods, qualification and acceptance conditions of plastic cable ties, used for the bundling, fixing and/or marking of cable harnesses in aircraft. The cable ties should be installed with a qualified application tool, which controls the application force thus avoiding damage to the cable insulation. It defines the aerospace requirements not specified in EN 62275.

DIN EN ISO 13628-5-2010石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

BS 6739-2009過程控制系統儀表的實施規范:安裝設計和實施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 50411-2-5-2009光纖通信系統用纖維組織和閉合.產品規范.1型S&A類鼓風纖維微管道電纜用密封閉路

This specification contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements which a fully installed blown fibre protected microduct closure must meet in order for it to be categorised as an EN standard product.These products are suitable for installation of and use with microduct fibre units, microduct optical fibre cables, microduct and protected microduct as defined within EN 60794-5.

BS EN 50411-2-9-2010光纖通信系統用纖維形成體和閉路.產品規范.S&A類鼓風纖維微管道電纜用非密封閉路

This specification contains the initial, start of life dimensional, mechanical and environmental performancerequirements which a fully installed blown fibre protected, non-sealed closure for duct and microductcable, must meet in order for it to be categorised as an EN standard product.These products are suitable for installation of and use with microduct fibre units, microduct optical fibrecables, microduct and protected microduct as defined within EN 60794-5.When the non-sealed closures are installed in subterranean environments it is mandatory to use sealedABF connectors meeting EN 50411-2-8 in order to guarantee the expected network performance andreliability.

BS EN ISO 13628-5-2009石油和天然氣工業.水下采油系統設計和操作.水下臍帶管

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.