釬焊用鋁合金復合板檢測

釬焊用鋁合金復合板檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 8005.1-2019鋁及鋁合金術語 第1部分:產品及加工處理工藝

GB/T 8005的本部分界定了鋁及鋁合金產品及加工處理工藝等方面涉及的術語和定義。本部分適用于鋁及鋁合金產品及加工處理工藝過程。

GB/T 25331-2010電力機車、電力動車組主變流器用水散熱器

本標準規定了電力機車、電力動車組主變流器用水散熱器的技術要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存等要求。本標準適用于電力機車、電力動車組主變流器用新造水散熱器的設計、制造和驗收。

GB/T 27675-2011鋁及鋁合金復合板、帶、箔材牌號表示方法

本標準規定了鋁及鋁合金復合板、帶、箔材牌號表示方法。本標準適用于鋁及鋁合金復合板、帶、箔材。

GB/T 31239-20141000kV變電站金具技術規范

本標準規定了1 000 kV變電站金具的一般技術要求、分類要求、連接與緊固、制造工藝和質量控制、試驗與檢驗、標志與包裝等。本標準適用于1 000 kV變電站內處于系統標稱電壓為1 000 kV的所有回路中構架跨線、設備間連接導體和絕緣子串的配套金具。

GB/T 33369-2016釬焊用鋁合金復合板、帶、箔材

本標準規定了釬焊用鋁合金復合板、帶、箔材的要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存及質量證明書與訂貨單(或合同)內容。本標準適用于釬焊用鋁合金復合板、帶、箔材(以下簡稱復合材)。

GB 50243-2016通風與空調工程施工質量驗收規范

本規范適用于工業與民用建筑通風與空調工程施工質量的驗收。本規范應與現行標準《建筑工程施工質量驗收統一標準》GB 50300配合使用。

JGJ/T 181-2009房屋建筑與市政基礎設施工程檢測分類標準

本標準適用于房屋建筑和市政基礎設施工程檢測的分類。

YS/T 446-2011釬焊式熱交換器用鋁合金復合箔、帶材

本標準規定了釬焊式熱交換器用鋁合金復合箔、帶材的術語、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存及質量證明書與訂貨單（或合同）內容。本標準適用于釬焊式熱交換器用鋁合金復合箔、帶材。

YS/T 906-2013電站空冷用鋁合金復合帶

本標準規定了電站空冷釬焊式熱交換器用鋁合金復合帶的術語、要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存及質量證明書與訂貨單(或合同)內容。本標準適用于電站空冷釬焊式熱交換器用鋁合金復合帶(以下簡稱復合帶)。

DL/T 245-2012發電廠直接空冷凝汽器單排管管束

本標準規定了發電廠直接空冷凝汽器單排管管束的設計、制造、檢驗與驗收的要求。本標準適用于以冷凝水蒸氣為目的、設計壓力在-0.1MPa～0.045MPa、設計溫度在-40℃～120℃范圍內的敷鋁鋼管鋁翅片型直接空冷凝汽器單排管管束。本標準不適用于其他結構形式及其他有色金屬制造的管束。

ASTM B660-2002鋁及鎂制品的封裝/包裝標準規范

1.1 These practices describe methods of packaging/packing aluminum and magnesium products, in preparation for storage or shipment, both foreign and domestic. Assuming proper and normal handling in transit, these practices are designed to deliver the products to their destination in good condition. For DoD redistribution, see Supplementary Requirements.1.2 Aluminum and magnesium products must be preserved and packed so as to be adequately protected from possible damage during shipment and storage. Major damage types are:1.2.1 Mechanical, including bending, crushing, denting, scratching, or gouging during handling and storage; and abrasions resulting from vibration during transport of the material.1.2.2 Corrosion, or water stain, resulting from exposure of packed material to water, either externally applied, or as condensate caused by temperature variations in a humid atmosphere. Note 18212;A complete metric companion to Practices B 660 is being developed-Practices B 660M; therefore, no metric equivalents are presented in these practices.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

DIN EN 12258-1-2012鋁和鋁合金.術語和定義.第1部分:一般術語.三種語言版本EN 12258-1-2012

To update the terms and definitions to be used in CEN/TC 132 standards. The document defines general terms which are helpful for the communication within the aluminum industry and its customers relating to products of aluminium and aluminium alloys. Definitions in other standards applying to a particular field of application can be more specific than the definitions of identical terms in this standard; these can be found in the relevant standards.

BS EN 14324-2004銅焊.銅焊接合的應用指南

This document gives guidance on the application of brazing and the manufacture of brazed joints. This standard gives an introduction to brazing and a basis for the understanding and use of brazing in different applications. Because of the wide range of applications of brazing this standard does not give detailed guidance that might be product specific. For such information reference should be made to the appropriate product standard or, for applications where this does not exist, the relevant criteria should be clearly established before any brazing is undertaken.\nThis standard covers joint design and assembly, material aspects for both parent material and filler materials, brazing process and process variables, pre- and post-braze treatment and inspection.