動力鋰電池用鋁殼檢測

動力鋰電池用鋁殼檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

JT/T 373-1998斗輪式堆取料機修理技術規范

本標準規定了斗輪式堆取料機的修理技術要求本標準適用于生產能力為1000r/h及以上的在條形料場軌道上行走的臂式斗輪堆取料機，臂式斗輪取料機、臂式堆料機及其它形式的同類斗輪機也可參照使用從國外進口的大型斗輪堆取料機的修理，可按廠家提供的圖樣資料和技術要求進行，若資料不全時應按本標準執行。

YS/T 914-2013動力鋰電池用鋁殼

本標準規定了動力鋰電池用鋁殼的要求、試驗方法、檢驗規則及標志、包裝、運輸、貯存、質量證明書和合同(或訂貨單)內容。本標準適用于各種動力鋰離子電池用鋁殼。

DL 5027-2015電力設備典型消防規程

本規程規定了電力設備及其相關設施的防火和滅火措施，以及消防安全管理要求，適用于發電單位、電網經營單位，以及非電力單位使用電力設備的消防安全管理。電力設計、安裝、施工、調試、生產應符合本規程的有關要求。本規程不適用于核能發電單位。

UL 1740-2007機器人和自動設備

These requirements cover robots and robotic equipment rated 600 V or less and intended for installation in accordance with the National Electrical Code, ANSI/NFPA 70. Since end-use installation of a robot and robotic equipment may vary for each user application, guidelines for end-product installation may be evaluated to the applicable sections of ANSI/RIA R15.06, Standard for Industrial Robots and Robot Systems-Safety Requirements. Portions of the requirements in this Standard have been excerpted from the Robotic Industries Associations (RIA) Standard for Industrial Robots and Robot Systems - Safety Requirements, ANSI/RIA R15.06. These requirements cover robotic equipment and systems intended for indoor and outdoor use in applications such as parts assembly, parts transfer, automated material handling, inspection, loading, diecasting, deburring, welding, paint spraying, clinical/diagnostic systems, pharmaceutical applications, commercial food processing, automated vehicle refueling systems, library book handling/sorting, clean room applications, medical use for surgery, mobile robots, automated guided vehicles, automated storage/retrieval systems, and the like. Unique features or functions associated with the robotic application, not specifically addressed in this Standard, shall also be evaluated to other applicable Standards/requirements. These may include, but are not limited to, Electrical Equipment for Laboratory Use; Part 1: General Requirements, UL 3101-1; Medical and Dental Equipment, UL 544; Power Operated Pumps for Petroleum Product Dispensing Systems, UL 79. In addition to the requirements in this Standard, robots and robotic systems shall also comply with the applicable sections of the Electrical Standard for Industrial Machinery, ANSI/NFPA 79. Robots and robotic systems intended for use in hazardous locations, as defined by the National Electrical Code ANSI/NFPA 70, shall also comply with the requirements in Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III, Division 1, Hazardous (Classified) Locations, UL 913. In the following text, a requirement that applies to one type of equipment, such as a controller or teach pendant, will be identified by a specific reference. In the absence of a specific reference or if the term robot or robotic equipment is employed, it is to be understood that the requirement applies to all types of equipment covered by this Standard.

UL 6142-2012小型風力發電機系統的安全性標準

These requirements cover small wind turbine systems (WT) and electrical subassemblies. With respect to this standard, small WT are considered to be wind turbines where a user or service person cannot or is not intended to enter the turbine to operate it or perform maintenance. These units are intended for use in stand-alone (not grid-connected) or utility interactive applications. Utility-interactive,grid-tied WT are operated in parallel with an electric power system (EPS) to supply power to common loads.

UL SUBJECT 2755-2011模塊化數據中心的研究概況

1.1 This Outline of Investigation covers Modular Data Centers (MDC). The Modular Data Centers coveredby these requirements are pre-fabricated units consisting of an outer enclosure housing ITE and varioussupport equipment such as electrical service and distribution equipment, HVAC systems and the like.Some configurations may have the support equipment housed in a separate enclosure. A typicalconstruction may use a standard ISO shipping container or other structure as the outer enclosure, racksor cabinets of ITE, NEC compliant service entrance equipment and power distribution components, powerstorage such as a UPS and an air or liquid cooling system.1.2 These factory-built modules incorporate pre-installed materials and equipment which, afterinstallation, may be concealed and may not be accessible for inspection at the final installation site.1.3 The modular data centers covered by these requirements are intended for fixed installation eitherindoors or outdoors based on their construction and resistance to environmental conditions. MDCsintended for outdoor use shall be identified with a NEMA environmental class rating.1.4 These requirements are intended to demonstrate compliance with the National Electrical Code (NEC),NFPA 70 and other national Codes such as Building, Fire, Plumbing, Mechanical, and the like. Wherestate or local codes differ from the national codes anticipated by these requirements, determiningcompliance with these codes is the responsibility of the local authority having jurisdiction.1.5 When these requirements do not cover a specific technology or construction feature, the applicablerequirements of the National Codes shall be used.1.6 This Outline of Investigation assumes that the final installation of the MDC will be performed byqualified service personnel in accordance with the applicable installation instructions, installation practicesand national installation codes. These MDCs are intended for installation subject to approval by theAuthority Having Jurisdiction.

BS 6739-2009過程控制系統儀表的實施規范:安裝設計和實施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.