百葉窗用鋁合金帶材檢測

百葉窗用鋁合金帶材檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 19775-2005玻璃-金屬封接式熱管真空太陽集熱管

本標準規定了玻璃-金屬封接式熱管真空太陽集熱管的術語和定義、分類與命名、技術要求、檢測方法、檢驗規則及標志、包裝、運輸、貯存。 本標準僅適用于玻璃-金屬封接式熱管真空太陽集熱管。

GB/T 37256-2018建筑室外用格柵通用技術要求

本標準規定了建筑室外用格柵的術語和定義、分類和標記、材料、一般要求、要求和試驗方法。本標準適用于建筑外圍護結構中的固定格柵。

LY/T 2885-2017竹百葉窗簾

本標準規定了竹百葉窗簾的術語和定義、分類、要求、檢驗方法、檢驗規則以及標志、包裝、運輸和貯存。本標準適用于室內用竹質百葉窗簾。

JG/T 251-2017建筑用遮陽金屬百葉簾

本標準規定了建筑用遮陽金屬百葉簾的分類、代號及標記、材料和配件、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于建筑用外遮陽、內遮陽、中間遮陽的金屬百葉簾。本標準不適用于內置遮陽中空玻璃用金屬百葉簾。

JG/T 274-2018建筑遮陽通用技術要求

本標準規定了建筑遮陽產品的術語和定義、分類和標記、材料及配件、要求和試驗方法等。本標準適用于安裝在建筑物上的遮陽產品，包括外遮陽產品、內遮陽產品和中間遮陽產品。

NF P28-002-1-2-2008建筑施工工程.隔墻.第1-2部分:材料選擇用一般標準

Le présent document a pour objet de fixer les critères généraux de choix des matériaux utilisés pour la réalisation de fa?ades telles que définies dans le domaine d'application de la NF DTU 33.1 P1-1 (CCT).

DIN EN ISO 13706-2012石油、石化和天然氣工業.風冷熱交換器

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and natural gas industries. This International Standard is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.

BS 1703-2005垃圾道和垃圾斗規范

This British Standard specifies requirements for gravity transport systems for refuse in multi-storey buildings, consisting of refuse chutes in the form of one or more vertical pipes, complete with hoppers, receiving refuse from successive floors in a building and discharging it into a refuse storage system.

BS 7412-2007未增塑聚氯乙烯(PVC-U)擠制空心型窗和門具規范

This British Standard specifies requirements for the design, fabricationand performance of windows and glazed doorsets made from PVC-Uextruded hollow profiles.This British Standard applies to windows and doorsets manufacturedfrom PVC-U hollow profiles incorporating fusion welded corner joints.It applies to windows and doors fabricated into frames in a factory, tobe installed vertically (within 15°) into the external face of buildings, assingle or multi-light units, in coupled assemblies when appropriate, ofthe following types:a) windows:1) hinged: side-hung (open in or out), top-hung (open out),bottom-hung (open in), tilt and turn or turn before tilt;2) projecting: side-hung (open in or open out) and top-hung(open out or reversible);3) pivoted: horizontal and vertical (hung centrally or off-centre)including reversible;4) sliding: horizontal and vertical;5) side-hung: fully reversible;6) fixed light;b) doors:1) single leaf single-swing doors with or without side lights andtop panels;2) double leaf single-swing doors with or without side lights andtop panels.It is applicable to assemblies in which any frame member is not longerthan 3 m. It does not apply to curtain walls that span across horizontalstructural members of floors but is applicable to windows within acurtain walling system.It is applicable to assemblies up to the point of installation.NOTE Guidance on the evaluation of conformity is given in Annex A.Guidance on durability and recycling is given in Annex B.

BS EN 62109-1-2010光電電力系統中使用的電源轉換器安全性.第1部分:一般要求

This part of IEC 62109 applies to the power conversion equipment (PCE) for use inPhotovoltaic (PV) systems where a uniform technical level with respect to safety is necessary.This standard defines the minimum requirements for the design and manufacture of PCE forprotection against electric shock, energy, fire, mechanical and other hazards.This standard provides general requirements applicable to all types of PV PCE. There areadditional parts of this standard that provide specific requirements for the different types ofpower converters, such as Part 2 - inverters. Additional parts may be published as newproducts and technologies are commercialised.