燃氣器具快速切斷裝置檢測

燃氣器具快速切斷裝置檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 35848-2018商用燃氣燃燒器具

本標準規定了商用燃氣燃燒器具(以下簡稱燃具)的術語和定義，分類和型號，要求，試驗方法，檢驗規則，標志、警示和說明書，包裝、運輸和貯存。本標準適用于以符合GB/T 13611規定的燃氣為能源，燃燒用空氣取自室內、燃燒產物直接或間接排向室外的燃具，包括：a)　額定熱負荷不大于80 kW、蒸汽壓力不大于80 kPa，且設計正常水位水容積小于30 L的蒸汽發生器類燃具；b)　額定熱負荷不大于80 kW、蒸腔蒸汽壓力不大于500 Pa的蒸箱類燃具；c)　額定熱負荷不大于50 kW、腔體內壓力不大于80 kPa的炸爐類燃具；d)　額定熱負荷不大于50 kW的煮食爐類燃具；e)　額定熱負荷不大于80 kW、鍋口有效直徑不小于600 mm的大鍋灶類燃具；f)　額定熱負荷不大于10 kW的煲仔爐，額定熱負荷不大于50 kW的矮湯爐等平頭爐類燃具；g)　額定熱負荷不大于100 kW的常壓固定式沸水器類燃具；h)　燜飯量大于等于6L的飯鍋類燃具；i)　額定熱負荷不大于50 kW的洗碗機類燃具；j)　額定熱負荷不大于60 kW的炒灶類燃具；k)　額定熱負荷不大于50 kW的燒烤爐類燃具；l)　額定熱負荷不大于35 kW的熱板爐類燃具；m)　額定熱負荷不大于80 kW的烤箱類燃具；n)　以上產品的組合體。

GB/T 36699-2018鍋爐用液體和氣體燃料燃燒器技術條件

本標準規定了鍋爐用液體和氣體燃料燃燒器的分類與型號編制、組成與基本配置、基本要求、性能要求、設計與制造、檢驗、試驗與檢測、技術文件與標識、包裝、運輸和貯存、安裝、調試與使用等方面的技術要求。本標準適用于鍋爐用液體和氣體燃料的強制鼓風燃燒器和自然通風燃燒器。電站鍋爐啟動燃燒器、各類工業窯爐與工業加熱爐及其他用途燃燒器可參照本標準執行。

GB/T 50811-2012燃氣系統運行安全評價標準

本規范適用于已正式投產運行的面向居民、商業、工業企業、汽車等領域燃氣系統的現狀安全評價。本標準不適用于燃氣的生產、城市門站以前的天然氣管道輸送，以及沼氣、秸稈氣的生產和使用。

CJ/T 113-2015燃氣取暖器

本標準規定了燃氣取暖器(以下簡稱取暖器)的術語和定義,分類與型號,結構和材料,要求,試驗方法,檢驗規則,標識和說明書,包裝、運輸和貯存。本標準適用于使用GB/T 13611規定的燃氣的取暖器,包括:a) 額定熱輸入不大于20 kW的家用取暖器;b) 單個燃燒器額定熱輸入不大于120 kW的非家用取暖器。本標準不適用于室外使用的取暖器、冷凝式取暖器、專為工業用途設計的取暖器、在移動的運輸交通工具中使用的取暖器。

CJ/T 398-2012家用燃氣用具電子式燃氣與空氣比例調節裝置

本標準規定了家用燃氣用具電子式燃氣與空氣比例調節裝置的術語和定義、縮略語、結構和材料、要求、試驗方法、檢驗規則、標識、安裝和操作說明書以及包裝、運輸和貯存。本標準適用于大工作壓力在10kPa以下、公稱直徑不大于DN50、使用GB/T 13611規定的城鎮燃氣器具用、閉環控制的能被單獨測試或作為燃氣用具（或燃燒器）部件進行測試的家用燃氣用具電子式燃氣與空氣比例調節裝置。

CJ/T 421-2013家用燃氣燃燒器具電子控制器

本標準規定了使用GB/T 13611規定的城鎮燃氣的家用燃氣燃燒器具用電子控制器（以下簡稱控制器）的術語和定義、分類、結構、要求、試驗方法、檢驗規則、標識、安裝和操作說明書、包裝、運輸和貯存。本標準適用于家用燃氣燃燒器具用電子控制器的生產和檢測。

CJ/T 451-2014商用燃氣燃燒器具通用技術條件

本標準規定了商用燃氣燃燒器具(以下簡稱燃具)的術語和定義,分類,結構和材料,要求,試驗方法,檢驗規則,標識、警示和使用說明書,包裝、運輸和貯存。本標準適用于商用廚房等使用,以符合GB/T 13611規定的燃氣為能源,安裝在室內、燃燒產物機械排至室外的燃燒器具。

DB31/T 1011-2016燃氣用戶設施安全檢查技術要求

本標準規定了術語和定義、基本要求、檢查內容、記錄等內容。本標準適用于居民用戶和供氣壓力＜0.01 MPa的非居民用戶使用的燃氣用戶設施的安全檢查。

EN 30-1-1-2008家用燃氣灶具.第1-1部分:安全性.一般性;包含修改件A1-2010

This European Standard specifies the construction and performance characteristics as well as the requirements and methods of test for the safety and marking of freestanding and built-in domestic cooking appliances burning the combustible gases given in 4.1 according to the categories specified in 4.2, referred to in the text as \"appliances\".This European Standard covers the following types of domestic cooking appliances, as defined in Clause 3, and belonging to the classes defined in 4.3 (see Table 1): independent freestanding hotplates; independent built-in hotplates; independent hotplates and grills; table cookers; freestanding ovens; built-in ovens; freestanding or built-in grills; griddles; freestanding cookers; built-in cookers. Unless specifically excluded hereafter,This European Standard applies to these appliances or their component parts, whether or not the component parts are independent or incorporated into a single appliance, even if the other heating components of the appliance use electrical energy (e. g. combined gas-electric cookers).This European Standard includes requirements covering the electrical safety of equipment incorporated in the appliance that is associated with the use of gas. It does not include requirements covering the electrical safety of electrically-heated component parts or their associated equipment1).This European Standard does not apply to: a) outdoor appliances; b) appliances connected to a combustion products evacuation duct; c) appliances having a pyrolitic gas oven; d) appliances having covered burners which are not in conformity with the constructional requirements of 5.2.8.2.2; e) appliances incorporating flame supervision devices and having an automatic ignition device for which the duration of the ignition attempt is limited by design; f) appliances equipped with a burner that is periodically ignited and extinguished under the control of an automatic on/off device; 1) Refer to the electrical safety rules. g) appliances equipped with an oven and/or with a grill having a fan: 1) either for the supply of combustion air or for the evacuation of the products of combustion; 2) or for the circulation of the products of combustion within the compartments; h) appliances supplied at pressures greater than those defined in 7.; i) appliances having one or more burners that are capable of remote operation (type1 or type 2), unless the burner(s) concerned are thermostatically controlled oven burners of time-controlled ovens that are designed for a delayed start without the user being present; j) appliances incorporating one or more hotplate or grill burners that enable the user to program the cooking cycle, including the start and/or the end of the cycle.This European Standard does not cover the requirements relating to third family gas cylinders, their regulators and their connection.This European Standard only covers type testing.

EN 88-1-2011燃氣器具用壓力調節器和相關安全裝置.入口壓力大為50 kPa及以下的壓力調節器

This European Standard specifies the safety, construction and performance requirements for pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulator), intended for use with gas burners, gas appliances and similar use, hereafter referred to as `pressure regulators'.This European Standard is applicable to pressure regulators with declared maximum inlet pressures up to and including 50 kPa (500 mbar) of nominal connection sizes up to and including DN 250 for use with one or more fuel gases in accordance with EN 437, pressure regulators which use auxiliary energy, pneumatic gas/air ratio pressure regulators, which function by controlling a gas outlet pressure in response to an air signal pressure, air signal differential pressure, and/or to a furnace pressure signal (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulator), gas/air ratio pressure regulators which change an air outlet pressure in response to a gas signal pressure or a gas signal differential pressure.This European Standard does not cover pressure regulators connected directly to gas distribution network or to a container that maintains a standard distribution pressure, pressure regulators intended for gas appliances to be installed in the open air and exposed to the environment, mechanically linked gas/air ratio controls, electronic gas/air ratio controls (EN 12067-2).

EN 1319-2009凈加熱輸入量不超過70kW的帶有風扇輔助鍋爐的家用空間加熱燃氣強制對流空氣加熱器

This European Standard specifies the requirements and test methods for the safety and efficiency of domestic gas-fired air heaters with a fan to assist the transportation of combustion air and/or combustion products, hereafter referred to as appliances.This European Standard applies to Type B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with an input not exceeding 70 kW (net cv basis), intended primarily for use in single unit residential dwellings. Provision of the heated air may be by means of ducting.This standard does not apply to: a) appliances of the condensing type; b) appliances for outdoor installation; c) dual purpose air conditioning appliances (heating and cooling); d) appliances where the air is heated by an intermediate fluid; e) appliances with forced draught package burners or fully premixed burners; f) appliances fitted with a manual means of adjusting the combustion air supply or the evacuation of the combustion products; g) portable or transportable forced convection appliances; h) appliances having multiple heating units with a single draught diverter; i) appliances fitted with more than one flue outlet; j) Type C22, C23, C42, C43, C52 and C53 appliances; k) appliances that are designed for continuous condensation within the flue system under normal operating conditions; l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic.This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.

NF D35-354-2008專用液化石油氣裝置用規范.家用無煙道空間加熱器(包括擴散式催化燃燒加熱器)

La présente Norme européenne spécifie les prescriptions, les méthodes d'essais et le marquage des appareils domestiques de chauffage non raccordés à un conduit d'évacuation des produits de la combustion, y compris les appareils à combustion catalytique diffusive, dont le débit calorifique nominal est inférieur à 4,2 kW (HS), alimentés par des gaz de la 3e famille sous la pression nominale de service ne dépassant pas 50 mbar, désignés dans le texte par \"appareils\".La présente Norme européenne est applicable aux types d'appareils suivants : appareils fixes fonctionnant au butane commercial et/ou au propane commercial ; appareils portatifs ou mobiles fonctionnant soit au butane commercial, soit au butane commercial et au propane commercial, y compris ceux qui ont un compartiment d'installation pour une bouteille portative rechargeable de gaz de pétrole liquéfié.Aucune prescription particulière concernant le rendement thermique n'est définie pour ces types d'appareils car toute la chaleur produite par le processus de la combustion se dégage dans l'espace à chauffer ; les exigences concernant la combustion, qui relèvent de la sécurité, garantissent la combustion du combustible gazeux.La présente Norme européenne ne concerne pas les appareils incorporant des dispositifs électriques de contr?le du gaz.L'annexe A donne les détails concernant les catégories d'appareils commercialisées dans les divers pays.Les exigences pour les appareils données dans cette norme européenne supposent que l'alimentation en gaz à partir de la bouteille soit contr?lée par un détendeur dont la pression nominale maximale de détente atteint 50 mbar.La présente norme européenne ne concerne pas les bouteilles de gaz de pétrole liquéfié, ni leurs détendeurs associés, ni les tubes et tuyaux flexibles, qui doivent être conformes aux réglementations nationales en vigueur. La présente norme couvre uniquement les essais de type.

NF P45-204-7-2008建筑工程.家用房屋中氣體裝置.第7部分:計算規則

Le présent document fixe des règles de calcul pour :- dimensionner des canalisations d'alimentation en gaz combustibles et en hydrocarbures liquéfiés des appareils installés dans les batiments d'habitation et de leurs dépendances,- dimensionner des systèmes d'évacuation des produits de combustion fonctionnant en tirage naturel des appareils de types B1 et B2 de débit calorifique nominal inférieur ou égal à 85 kW,- dimensionner les systèmes d'évacuation des produits de combustion des appareils installés en alvéoles techniques gaz,- déterminer le nombre admissible d'appareils de type C dont les terminaux débouchent dans les courettes fermées et les configurations en U.Les prescriptions applicables à ces différents cas sont présentées en Annexes A, B et C. Ces Annexes précisent également leur domaine d'application particulier respectif.

DIN 3386-2012大工作壓力小于或等于5 bar的空氣過濾器.試驗和要求

The available standard regulates requirements and examinations for gasfilters up to a nominal size of including DN 250, which operat with gases of DVGW-Arbeitsblatt G 260 (without LPG at liquid phase) at a maximum working pressure of 5 bar.

DIN EN 449-2008專用液化石油氣裝置用規范.無排氣口的居室暖器(包括擴散催化燃燒的加熱器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar. referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propane including those that incorporate a LPG container installation compartment for a transportable refillable liquefied petroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effective burning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

DIN EN 746-2-2011工業熱處理設備.第2部分:燃燒和燃料處理系統的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.