人造礦物纖維保溫材料檢測

人造礦物纖維保溫材料檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 51232-2016裝配式鋼結構建筑技術標準

本標準適用于抗震設防烈度為6度到9度的裝配式鋼結構建筑的設計、生產運輸、施工安裝、質量驗收與使用維護。

GBZ/T 211-2008建筑行業職業病危害預防控制規范

本標準規定了建筑行業職業病危害預防控制的基本要求、職業病危害因素的識別、防護措施及應急救援等要求。本標準適用于從事土木工程、建筑工程、線路管道和設備安裝工程及裝修工程的新建、擴建、改建和拆除等施工活動的企業、事業及個體經濟組織的職業病危害預防控制及衛生行政部門、建設主管部門和項目監理對施工企業的職業衛生監管。

CECS 445-2016非金屬面結構保溫夾芯板設計規程

本規程適用于工業與民用建筑采用的圍護結構、輕型屋面、吊頂板等用的非金屬面結構保溫夾芯板的設計。

JGJ/T 229-2010民用建筑綠色設計規范

本標準適用于新建、改建和擴建民用建筑的綠色設計。

CNS 3657-2017人造礦物纖維保溫材料

本標準適用于人造礦物纖維之保溫材料，且其制造原料不得含有石棉。

ASTM C1338-2014測量隔熱材料和飾面耐霉性的標準試驗方法

2.1x00a0;The type of materials used in the manufacture of insulation products and the type of membrane used to face these products can sometimes affect fungi sustenance in the presence of high humidity. 2.2x00a0;This test method is used to determine the relative ability of an insulation and its facing to resist fungal growth under conditions favorable for their development. 2.3x00a0;This test method uses a comparative material to determine the relative ability of a material to resist fungal growth. In some specialized product areas, it is required that no growth take place. In such cases, the use of the comparative material is omitted and the pass/fail criterion is based upon growth. 1.1x00a0;This test method covers the determination of the ability of new insulation materials and their facings to resist fungal growth. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM C1393-2000a(2006)管子和容器用垂直向礦物纖維薄板卷和薄板熱絕緣的標準規范

1.1 This specification covers the composition, dimensions, and physical properties of compression-resistant, perpendicularly oriented mineral fiber (rock, slag, or glass) roll and sheet insulation intended for use on flat, curved, or round surfaces up to 1000176;F (538176;C). This product (pipe and tank insulation) is typically used on nominal 24 in. (610 mm) or greater diameter surfaces. For specific applications, the actual use temperatures and diameters shall be agreed upon between the manufacturer and the purchaser.1.2 The orientation of the fibers within the roll or sheet insulation is essentially perpendicular to the heated/cooled surface (parallel to heat flow). This specification does not apply to flat block, board, duct wrap, or preformed pipe mineral fiber insulation where the insulation fiber orientation is generally parallel to the heated/cooled surface (across the heat flow).1.3 For satisfactory performance, properly installed protective vapor retarders must be used in low-temperature (below ambient) applications to prevent movement of water vapor through or around the insulation towards the colder surface.1.4 The values stated in inch-pound units are to be regarded as standard. The SI equivalents of inch-pound units are given in parentheses for information only and may be approximate.1.5 When the installation or use of thermal materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user-appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

EN 14015-2004在室溫及高于環境溫度液體儲存用平底,立式,圓柱形,現場建造的地面上可焊鋼罐的設計和制造規范

This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).

NF P84-207-1-2-2008建筑工程.帶防水涂層的承重木材和木制板屋頂.第1-2部分:材料選擇的通用標準(GCM)

Le présent document définit les critères de choix des matériaux à utiliser pour l'exécution de l'étanchéité de toitures de batiments comportant des éléments porteurs en bois ou panneaux dérivés du bois, faisant l'objet de la norme NF DTU 43.4 P1-1 Travaux de batiment - Toitures en éléments porteurs en bois et panneaux dérivés du bois avec revêtements d'étanchéité - Partie 1-1 : Cahier des clauses techniques types.

DIN 4102-4-2016建筑材料和建筑構件的耐火性能.概要和分級的建筑材料、構件和特種構件的應用

This document contains catagorized results of fire tests of buildings materials, components and construction types. Due to the assignment to the classes of building materials according to DIN 4102 part 1 and the fire resistance classes of the other parts of DIN 4102 respectively, further fire tests for the verification of usability required by the building regulations are not necessary.

DIN 4109-33-2016建筑物隔聲. 第33部分: 隔聲驗證使用數據 (組件目錄). 木結構, 輕型結構和干墻

This standard contains sound insulation specifications of components and structures for timber construction, lightweight construction and dry walling, which may be used without acoustic testing in the calculation procedures stated in DIN 4109-2 for the verification of the requirements of DIN 4109-1.

BS EN 14015-2004在室溫和高于室溫下液體儲存用現場建造的立式、圓柱形、平底、地上用焊接鋼罐的設計和制造規范

1 This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).\nThis document does not apply to tanks where the product is refrigerated to maintain it as a liquid at atmospheric pressure (see prEN 14620).\nThis document is concerned with the structural integrity of the basic tank structure and does not provide requirements for considering process design, operational issues, safety and firefighting facilities, in-service inspection, maintenance or repair. These aspects are covered in detail in other Codes of Practice (see Annex B).\n2 This document applies to closed-top tanks, with and without internal floating covers (see Annex C) and open-top tanks, with and without floating roofs (see Annexes D and E). It does not apply to 'lift-type' gas holders.\n3 This document applies to storage tanks with the following characteristics:\na) design pressure less than 500 mbar and design internal negative pressure not lower than 20 mbar (see 5.1 for pressure limitations);\nb) design metal temperature not lower than -40 ℃ and not higher than +300 ℃ (see 5.2.2);\nc) maximum design liquid level not higher than the top of the cylindrical shell.\n4 The limits of application of this document terminate at the following locations.\n— face of the first flange in a bolted flange connection;\n— first threaded joint on the pipe or coupling outside of the tank shell, roof or bottom;\n— first circumferential joint in a pipe not having a flange connection.\n5 This document is applicable to steel tanks with a maximum design strength ≤ 260 N/mm.\n6 In addition to the definitive requirements, this document also requires the items detailed in Annex A to be documented. For compliance with this document, both the definitive requirements and those required in Clause 4 have to be satisfied.\nnote:1) All pressures are in mbar gauge unless otherwise stated.