超級奧氏體不銹鋼檢測

超級奧氏體不銹鋼檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 15620-2008鎳及鎳合金焊絲

本標準規定了鎳及鎳合金實心焊絲和填充絲分類和型號、技術要求、試驗方法、檢驗規則、包裝、標志和品質證明書。本標準適用于溶化極氣體保護電弧焊、鎢極氣體保護電弧焊、氣焊及等離子弧焊等焊接用鎳及鎳合金實心焊絲和填充絲（以下簡稱焊絲）。

GB/T 20972.3-2008石油天然氣工業 油氣開采中用于含硫化氫環境的材料 第3部分:抗開裂耐蝕合金和其他合金

注意：按本部分選擇的耐蝕合金和其他合金，在油氣開采中規定的含硫化氫環境里是抗開裂的，但并不一定在所有的使用環境下都可避免開裂。為預期的使用環境選擇合適的耐蝕合金和其他合金是設備使用者的責任。GB/T 20972的本部分給出了在油氣開采及天然氣處理廠含硫化氫(HS)環境中，設備用耐蝕合金(CRA)和其他合金的選擇及評定的要求和推薦作法，這些設備的失效會對公眾、個人健康和安全或環境造成危害。使用本部分有助于避免設備發生這種代價高昂的腐蝕破壞。本部分是對那些合適的設計規范、標準和準則的補充，但不能代替它們對材料的要求。本部分?jǐn)⑹隽诉@些材料抗由硫化物應力開裂(SSC)、應力腐蝕開裂(SCC)和電偶誘發的氫應力開裂(GHSC)引起的破壞的性能。本部分只涉及開裂，不涉及均勻腐蝕(質量減少)或局部腐蝕造成的材料損失。本部分適用于按常規彈性準則設計和制造設備所用材料的選擇和評定。對于使用塑性準則的設計(例如基于應變和極限狀態設計)，按GB/T 20972.1-2007第5章的要求。本部分不一定適用于煉油或下游的加工設備。

GB/T 25151.2-2010尿素高壓設備制造檢驗方法 第2部分：尿素級超低碳鉻鎳鉬奧氏體不銹鋼選擇性腐蝕檢查和金相檢查

GB/T 25151的本部分規定了尿素超級低碳鉻鎳鉬奧氏體不銹鋼選擇性腐蝕深度和顯微組織檢查的試樣選取、制作、檢查項目和方法。本標準適用于尿素超級低碳鉻鎳鉬奧氏體不銹鋼晶間腐蝕試驗后的選擇性腐蝕檢查和金相檢查。

GB/T 25151.3-2010尿素高壓設備制造檢驗方法 第3部分：尿素級超低碳鉻鎳鉬奧氏體不銹鋼晶間腐蝕傾向試驗

GB/T 25151的本部分規定了尿素超級低碳鉻鎳鉬奧氏體不銹鋼在65%沸騰硝酸溶液中的腐蝕質量損失作為檢驗晶間腐蝕傾向的試驗方法。本部分適用于考察熱處理、焊接工藝對耐腐蝕性能的影響及檢測焊縫本身的耐腐蝕性能。

GB/T 25151.4-2010尿素高壓設備制造檢驗方法 第4部分：尿素級超低碳鉻鎳鉬奧氏體不銹鋼晶間腐蝕傾向試驗的試樣制取

GB/T 25151的本部分規定了尿素超級低碳鉻鎳鉬奧氏體不銹鋼晶間腐蝕傾向試驗的取樣。本部分適用于尿素超級低碳鉻鎳鉬奧氏體不銹鋼晶間腐蝕傾向試驗所用取樣。

GB/T 35146-2017石油天然氣工業 海上鉆井和修井設備

本標準規定了石油天然氣工業海上石油鉆井設備、修井設備和輔助設備的設計原則、材料、焊接、結構、試驗程序和要求。本標準適用于在各種類型移動式和固定式海上鉆井和修井平臺上新安裝使用的鉆井設備、修井設備和輔助設備的設計和建造，在役設備適用時可參照?qǐng)?zhí)行。本標準適用于從概念設計到建造完成的全部過程，也包括大修。本標準給出的技術和程序上的要求也適用于臨時安裝的設備。

GB/T 38807-2020超級奧氏體不銹鋼通用技術條件

本標準規定了超級奧氏體不銹鋼的術語及定義、分類、訂貨內容、尺寸、外形、重量、技術要求、試驗方法、檢驗規則、包裝、標志和質量證明書。本標準適用于公稱直徑或邊長不大于550 mm的熱軋或鍛制超級奧氏體不銹鋼鋼棒(以下簡稱鋼棒)。

GB 50236-2011現場設備、工業管道焊接工程施工規范

為提高工程建設施工現場設備和工業金屬管道焊接工程的施工水平，加強焊接工程施工過程的質量控制，保證工程質量和安全，制定本規范。本規范適用于碳素鋼、合金鋼、鋁及鋁合金、銅及銅合金、鈦及鈦合金（低合金鈦）、鎳及鎳合金、鋯及鋯合金材料的焊接工程的施工。本規范適用的焊接方法包括氣焊、焊條電弧焊、埋弧焊、鎢極惰性氣體保護電弧焊、熔化極氣體保護電弧焊、自保護藥芯焊絲電弧焊、氣電立焊和螺柱焊。焊接工程的施工，應按設計文件及本規范的規定執行。 當需要修改設計文件及材料代用時，必須經原設計單位同意,并出具書面文件。本規范應與現行標準《現場設備、工業管道焊接工程施工質量驗收規范》GB 50683配合使用。焊接工程的施工應符合現行的節能減排、環境保護、安全技術和勞動保護等有關規定。現場設備、工業管道焊接工程的施工除應符合本規范外，尚應符合現行有關標準的規定。

GB/T 50619-2010火力發電廠海水淡化工程設計規范

本規范適用于火力發電廠及核能發電廠的反滲透法和蒸餾法海水淡化系統設計。

GB 51156-2015液化天然氣接收站工程設計規范

本規范適用于陸上新建、擴建和改建的液化天然氣接收站工程的設計。

GB 51205-2016精對苯二甲酸工廠設計規范

本規范適用于精對苯二甲酸工廠生產裝置和輔助生產設施的新建、擴建和改建工程的設計，不包括為精對苯二甲酸工廠服務的公用工程設施和辦公設施。

DL/Z 1262-2013火電廠在役濕煙囪防腐技術導則

本標準規定了在役火電廠濕法脫硫煙囪改造的基本技術要求。本標準適用于在役火電廠濕法脫硫煙囪的防腐改造。

EN ISO 3506-2-2009耐腐蝕不銹鋼緊固件的機械特性.第2部分:螺母

This part of ISO 3506 specifies the mechanical properties of nuts made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 ℃ to 35 ℃. Properties vary at higher or lower temperatures.

DIN EN ISO 15156-3-2015石油和天然氣工業.油,氣生產中含硫化氫(H2S)環境下使用的材料.第3部分:耐裂化CRAs(防腐蝕合金)和其他合金(ISO 15156-3-2015).德文版本EN ISO 15156-3-2015

CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards, or regulations. This part of ISO 15156 addresses the resistance of these materials to damage that can be caused by sulfide stress-cracking (SSC), stress-corrosion cracking (SCC), and galvanically induced hydrogen stress cracking (GHSC). This part of ISO 15156 is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed. Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable, including permitted exclusions. This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see ISO 15156-1:2015, Clause 5. This part of ISO 15156 is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

BS EN ISO 3506-3-2009耐腐蝕不銹鋼緊固件的機械特性.不受拉伸應力作用的定位螺絲和同類緊固件

This part of ISO 3506 specifies the mechanical properties of set screws and similar fasteners not under tensile stress made of austenitic stainless steel, when tested over an ambient temperature range of 10 °C to 35 °C.Properties vary at higher or lower temperatures.This part of ISO 3506 applies to set screws and similar fasteners:- with nominal thread diameter 1,6 mm u d u 24 mm;- of triangular ISO metric threads with diameters and pitches in accordance with ISO 68-1, ISO 261 andISO 262;- of any shape.It does not apply to screws with special properties, such as weldability.NOTE The designation system of this part of ISO 3506 can be used for sizes outside the limits given in this clause (e.g. d > 24 mm), provided that all applicable mechanical and physical requirements of the hardness classes are met.This part of ISO 3506 does not define corrosion or oxidation resistance in particular environments.The aim of this part of ISO 3506 is the classification of corrosion-resistant stainless steel fasteners into hardness classes.Corrosion and oxidation performances and mechanical properties for use at elevated or sub-zerotemperatures can be agreed on between the user and the manufacturer in each particular case. Annex Dshows how the risk of intergranular corrosion at elevated temperatures depends on the carbon content.All austenitic stainless steel fasteners are normally non-magnetic in the annealed condition; after cold working, some magnetic properties can be evident (see Annex E).

BS EN ISO 3506-4-2009耐腐蝕不銹鋼緊固件的機械特性.攻絲螺釘

This part of ISO 3506 specifies the mechanical properties of tapping screws made from austenitic, martensitic and ferritic grades of corrosion-resistant stainless steels when tested at an ambient temperature range of 15 °C to 25 °C. Properties vary between higher and lower temperatures.It applies to tapping screws with threads from ST2,2 up to and including ST8 in accordance with ISO 1478.It does not apply to screws with special properties such as weldability.This part of ISO 3506 does not define corrosion or oxidation resistance in particular environments, however some information on materials for particular environments is given in Annex D. Regarding definitions of corrosion and corrosion resistance see ISO 8044.The aim of this part of ISO 3506 is a classification into property classes of corrosion-resistant stainless-steel fasteners.Corrosion and oxidation performances and mechanical properties for use at elevated or sub-zerotemperatures should be agreed between user and manufacturer in each particular case. Annex C shows how the risk of intergranular corrosion at elevated temperatures depends on the carbon content.All austenitic stainless-steel fasteners are normally non-magnetic in the annealed condition; after cold working, some magnetic properties may be evident (see Annex E).