空氣斷路器開關檢測

空氣斷路器開關檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 20840.6-2017互感器 第6部分:低功率互感器的補充通用技術要求

GB/T 20840的本部分規定了額定頻率為15 Hz~100 Hz的交流用途或直流用途的低功率互感器(LPIT)的補充通用技術要求。本產品標準以GB/T 20840.1為基礎，對相關的專項標準的條款進行了增補。本部分不包括互感器數字量輸出格式的技術規范。本部分限定了模擬量或數字量輸出的誤差。互感器數字接口的其他特性見GB/T 20840.9，并應用了變電站分層通訊結構的系列標準。本部分考慮了涉及帶寬的補充要求。諧波準確度要求和抗混疊濾波器要求列于附錄6A.4中。單相LPIT的通用框圖見圖601。依據采用的技術，并非圖601列出的所有部件皆為互感器必不可缺的。例如，對于無源低功率互感器(不包含有源電子器件的LPIT)，各框塊僅由無源元件構成且無電源。

GB/T 20840.8-2007互感器 第8部分:電子式電流互感器

本部分適用于新制造的電子式電流互感器，它具有模擬量電壓輸出或數字量輸出，供頻率為15Hz～10OHz的電氣測量儀器和繼電保護裝置使用。 第 12 章所列的準確度要求，適用于電氣測量儀器用電子式電流互感器。 第 13 章所列的準確度要求，適用于繼電保護裝置用電子式電流互感器，特別是那些以電流達額定電流很多倍時仍保持其準確度為主要要求的保護方式。如有要求，電子式電流互感器在電力系統故障時的暫態準確度也列于本章。 測量和保護兩用的電子式電流互感器應遵循本部分的所有條款，且被稱為多用途電子式電流互感器。 這種互感器技術可以用帶有電子器件的光學裝置，采用空心線圈（有或無內置積分器）或內裝并聯電阻的鐵心線圈作為電流變電壓的轉換器，它們可單獨使用或配裝電子器件。 對于模擬量輸出，電子式電流互感器可包括二次信號電纜。采用空心線圖及內裝并聯電阻的鐵心線圈的電子式電流互感器技術實例，列于附錄 D 。 對于數字量輸出，本部分采納電子式互感器到電氣測量儀器和電氣裝置為點對點鏈接（見附錄 E）。 為了保證這種點對點鏈接對整個變電站通訊系統的兼容性，從而允許所有各類變電站裝置之間的數據交換，增加了一些內容。這些內容建立了所謂點對點串行鏈接的鏈路層映射。總線通訊正在考慮中。 此映射允許不同制造單位的設備可以交互使用。 本部分既不規定特定的實施方案或產品，也不限定計算機系統的各種實施方案和接口。本部分規定各種實施方案的外部可見功能，以及這些功能所應遵守的要求。

YB 4408-2014高爐TRT系統電氣設備安裝工程施工驗收規范

本規范適用于高爐TRT系統電氣設備安裝工程施工驗收。

HB/Z 293-1996民用飛機電力應用和瞬態保護指南

本標準規定了在民用飛機用電設備的研制中，應考慮的供電電源形式以及供電電源的各種特性對用電設備的影響。規定在用電設備的研制以及機上布線中對電源瞬態的保護、干擾控制、饋電線保護、應急供電和應急用電設備等方面的要求。　　本標準適用于民用飛機用電設備的研制及飛機布線的設計。對供電系統與用電設備的協調起指導作用。但應注意協調本標準規定與承制方由于設備的特殊性而不適用的部分。

JGJ/T 365-2015太陽能光伏玻璃幕墻電氣設計規范

本規范適用于新建、擴建和改建的接入交流220V/380V電壓等級用戶側的并網或離網太陽能光伏玻璃幕墻及采光頂的電氣設計。

TB/T 2993.2-2016鐵路通信電源 第2部分:通信用高頻開關電源系統

TB/T 2993的本部分規定了鐵路高頻開關電源系統的術語、定義和縮略語，產品組成和分類，技術要求，試驗方法，檢驗規則，標志、包裝、運輸和儲存。本部分適用于鐵路高頻開關電源系統的設計、制造和檢驗。

TB/T 3445-2016機車電氣重聯技術規范

本標準規定了機車電氣重聯的組成、技術要求、重聯功能檢查與試驗。本標準適用于交流傳動機車電氣控制重聯的設計、制造和試驗。

DIN EN 1012-3-2014壓縮機和真空泵. 安全要求. 第3部分:加工壓縮機; 德文版本EN 1012-3-2013

This part of EN 1012 is applicable to compressors having an operating pressure greater than 0,5 bar and designed to utilise all gases other than air, nitrogen or inert gases which are covered in part 1. The standard lists the significant hazards associated with compressors and specifies safety requirements applicable to the design, installation, operation, maintenance and dismantling of compressors during their foreseeable lifetime and subsequent disposal.This part of EN 1012 includes under the general term compressors, those machines which comprise;- the compressor itself- a prime mover- any component or device supplied which is necessary for safe operation of the compressor.In addition it applies to partly completed compressors having a compressor in combination with some of these components as well as compressor assemblies operating in combination.Excluded are refrigerant compressors used in refrigerating systems or heat pumps as defined in EN 378-1.

DIN EN 3197-2011航空航天系列.飛行器電子和光學互連系統;德文版本和英文版本EN 3197-2010

The document provides instructions on the methods to be used when installing, repairing or modifying aircraft electrical and optical fibre interconnection systems, subject to the limitations defined in 4 of this document.

BS EN 60044-8-2002儀表變壓器.電流變壓器

This part of IEC 60044 applies to newly manufactured electronic current transformers havingan analogue voltage output or a digital output, for use with electrical measuring instrumentsand electrical protective devices at nominal frequencies from 15 Hz to 100 Hz.NOTE Additional requirements due to the bandwidth are considered. The accuracy requirements on harmonics aregiven in annex D.Clause 12 covers the accuracy requirements that are necessary for electronic currenttransformers for use with electrical measuring instruments.Clause 13 covers the accuracy requirements that are necessary for electronic currenttransformers for use with electrical protective relays, and particularly for forms of protection inwhich the prime requirement is to maintain the accuracy up to several times the rated current.If required, the transient accuracy of an electronic current transformer during fault is also givenin this clause.Electronic current transformers intended for both measurement and protection should complywith all the clauses of this standard and are called multipurpose electronic currenttransformers.The transformer technology can be based on optical arrangements equipped with electricalcomponents, on air-core coils (with or without a built-in integrator), or on iron-core coils withintegrated shunt used as a current-to-voltage converter, alone or equipped with electroniccomponents.For analogue output, the electronic current transformer may include the secondary signalcable. Examples of electronic current transformer technologies using air-core coils and ironcorecoils with integrated shunt are given in annex C.For digital output, this standard takes into account a point-to-point connection from theelectronic transformer to electrical measuring instruments and electrical devices (see annex B).Some information has been added in order to ensure the compatibility of this point-to-point linkwith the overall system of communication in the substation, thus allowing data exchangebetween all kinds of substation devices. This information builds what is called the mapping ofthe link layer of the point-to-point serial link. Processbus communication is underconsideration.This mapping allows interoperability between devices from different manufacturers.This standard does not specify individual implementations or products, nor does it constrain theimplementation of entities and interfaces within a computer system. This standard specifies theexternally visible functionality of implementations together with conformance requirements forsuch functionalities.