電氣和電子設備電壓檢測

電氣和電子設備電壓檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

HB/Z 293-1996民用飛機電力應用和瞬態保護指南

本標準規定了在民用飛機用電設備的研制中，應考慮的供電電源形式以及供電電源的各種特性對用電設備的影響。規定在用電設備的研制以及機上布線中對電源瞬態的保護、干擾控制、饋電線保護、應急供電和應急用電設備等方面的要求。　　本標準適用于民用飛機用電設備的研制及飛機布線的設計。對供電系統與用電設備的協調起指導作用。但應注意協調本標準規定與承制方由于設備的特殊性而不適用的部分。

UL 61496-1-2002電敏保護設備.第1部分:一般要求和試驗

This part of IEC 61496 specifies general requirements for the design，construction and testing of ELECTRO—SENSITIVE PROTECTIVE EQUIPMENT(ESPE)for the safeguarding of machinery Special attention is di rected tofunctional and design requirements that ensure an appropriate safety related performance is achieved AnESPE may include optional safety-related functions，the requirements for which are given in annex AThe particular requirements for specific types of sensing function are given in other parts of this standardThis standard does not specify the dimensions or configuration of the DETECTION ZONE and its disposition inrelation to hazards in any particular application，nor what constitutes a hazardous state of any machineIt is restricted to the functioning of the ESPE and how it inte rfaces with the machineThis standard may be relevant to applications other than those for the protection of persons，for examplefor the protection of machinery or products frOm mechanical damage In those applications additionalrequirements may be necessary，for example when the materials that have to be recognized by thesensing function have different propedies from those of personsThis standard does not deal with electromagnetic compatibility(EMC)emission requirementsThis part of IEC 61496 provides general requirements for ESPES of various types employing differentmethods of sensing The particular requirements for specific types of sensing function will be covered insubsequent parts of this standa~The requirements for ESPES using active opto—electric protective devices，e g light curtains a re contained in part 2This pa rt refers to the technical suitability of the electro—sensitive protective equipment Its application mayrequire the use of substances and／or test procedures that could be inju rious to health unless adequateprecautions were taken Conformance with this standard in no way absolves either the SUPPLIER or the userfmm statutory obligations relating to the safety and health of persons du ring the use of the equipmentcovered by this standard

DIN EN 61676-2010醫用電氣設備.診斷放射學中X射線管電壓的非侵入性測量用劑量測定儀器

The standard specifies the performance requirements of instruments as used in the non-invasive measurements of X-ray tube voltage up to 150 kV and the relevant compliance tests.

BS EN 50123-4-2003+A1-2013軌道交通.固定設備.直流開關裝置.室外直流切斷開關、負荷開關和接地開關

To be read in conjunction with BS EN 50123-1:2003

BS EN 60896-21-2004固定式鉛酸蓄電池組.閥門調節型.試驗方法

This part of IEC 60896 applies to all stationary lead-acid cells and monobloc batteries of thevalve regulated type for float charge applications, (i.e. permanently connected to a load andto a d.c. power supply), in a static location (i.e. not generally intended to be moved from placeto place) and incorporated into stationary equipment or installed in battery rooms for use intelecom, uninterruptible power supply (UPS), utility switching, emergency power or similarapplications.The objective of this part of IEC 60896 is to specify the methods of test for all types andconstruction of valve regulated stationary lead acid cells and monobloc batteries used instandby power applications.This part of IEC 60896 does not apply to lead-acid cells and monobloc batteries used forvehicle engine starting applications (IEC 60095 series), solar photovoltaic energy systems(IEC 61427), or general purpose applications (IEC 61056 series).