1001kV交流系統用靜電防護服裝檢測

1001kV交流系統用靜電防護服裝檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 1001.1-2021標稱電壓高于1 000 V的架空線路絕緣子 第1部分:交流系統用瓷或玻璃絕緣子元件 定義、試驗方法和判定準則

本文件界定了架空線路用瓷或玻璃絕緣子元件(以下簡稱絕緣子)的術語和特性，規定了檢驗特性規定值的條件、試驗方法和判定準則。本文件適用于標稱電壓高于1 000 V、頻率不超過100 Hz交流架空電力和牽引線路用瓷和玻璃絕緣子，以及直流架空電力牽引線路用絕緣子的定義、試驗方法和判定準則。本文件也適用于絕緣子串元件、架空線路剛性絕緣子和變電所用的類似結構的絕緣子的定義、試驗方法和判定準則。本文件不適用于構成電氣部件的絕緣子，或電氣結構中的部件，以及GB/T 8287(所有部分)中所包括的支柱絕緣子的定義、試驗方法和判定準則。絕緣子串和絕緣子組的試驗方法(如，濕操作沖擊電壓)和接收準則在GB/T 1001.2—2010中論述。本文件不包括有關按特定運行條件選擇絕緣子的要求。絕緣子的特性值在相應的產品標準中規定。

GB/T 1001.2-2010標準電壓高于1000V的架空線路絕緣子 第2部分：交流系統用絕緣子串及絕緣子串組 定義、試驗方法和接收準則

GB/T 1001的本部分規定了標準電氣試驗程序及接收規則，以檢驗本部分范圍內的絕緣子串和絕緣子串組的規定特性。本部分適用于標準電壓高于1000V、頻率不大于100Hz的架空電力線路用瓷或玻璃絕緣子串元件組成的絕緣子串和絕緣子串組。本部分也適用于直流架空牽引線路用的絕緣子串和絕緣子串組。本部分還適用于變電所用的類似結構的絕緣子串和絕緣子串組。本部分還可作為直流架空電力線路用的絕緣子串和絕緣子串組及復合絕緣子的暫用標準。

QJ 10013-2008氫氧火箭發動機試驗系統安全規定

本標準規定了氫氧火箭發動機試驗系統的安全要求及應急處理。本標準適用于氫氧火箭發動機(以下簡稱發動機)及組件地面試驗，火箭氫氧子級動力系統試驗系統可參照執行。

TB 10010-2016鐵路給水排水設計規范

本規范適用于新建、改建鐵路給水排水工程設計。

TB 10016-2016鐵路工程節能設計規范

本規范適用于新建、改建鐵路工程設計。

TB 10018-2018鐵路工程地質原位測試規程

本規程適用于新建與改建鐵路勘察設計、施工、運營等階段的工程地質原位測試工作。

JB/T 10017-2012帶表卡規

本標準規定了帶表卡規的術語和定義、型式與基本參數、要求、試驗方法、檢查條件、檢查方法、標志與包裝等。本標準適用于測量范圍上限不大于400mm，分度值為0.005mm、0.01mm、0.02mm、0.05mm、0.1mm的指針式帶表卡和分辨力為0.005mm、0.01mm、0.02mm的數顯帶表卡規（統稱為“帶表卡規”）。

DL/T 1001-2006復合絕緣高壓穿墻套管技術條件

本標準規定了復合絕緣高壓穿墻套管的技術要求、試驗方法、檢驗規則以及標志、包裝、運輸及儲存。 本標準適用于標稱電壓35kV及以上電壓等級、頻率為50Hz～60Hz的交流系統電站和變電所配電裝置用的戶外—戶內電容式復合絕緣穿墻套管（以下簡稱套管）。安裝地點的海拔為1000m以下，環境溫度為-40℃～+40℃。

ASTM F1001-1999a防護服裝材料評估用化學試劑的選擇

1.1 The purpose of this guide is to provide a recommended list of both liquid and gaseous chemicals for evaluating protective clothing materials in testing programs. 1.2 Results derived from testing programs using these lists of challenge chemicals are not intended for the definitive characterization of protective clothing materials. 1.3 This list of challenge chemicals is not inclusive of all chemical challenges; the chemicals were chosen to represent broad ranges of liquid and gaseous chemical classes and properties. Not all chemical classes are represented. Other chemicals, especially those of interest to the manufacturer or user, should be tested in addition to those recommended in this guide. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazards statement is given in Section 7.

ASTM F1001-1999a(2006)防護服裝材料評估用化學試劑的選擇標準指南

This guide establishes a recommended list of challenge chemicals to encourage those who evaluate chemical protective clothing to test a minimum number of chemicals in common. This list will simplify the comparison of data from different sources. This guide may also serve material developers or evaluators in screening candidate protective clothing materials. Test methods applicable to the use of this guide include, but are not limited to, Test Methods F 903 and F 739. 5.3.1 The battery of chemical gases shall not be used for testing material penetration resistance because Test Method F 903 has been designed for measuring liquid penetration only. 5.3.2 Evaluation of materials against the gaseous chemical battery is primarily intended for those materials used in the construction of totally-encapsulating protective suits or other clothing items that are designed to prevent exposure to chemical vapors or gases. 1.1 The purpose of this guide is to provide a recommended list of both liquid and gaseous chemicals for evaluating protective clothing materials in testing programs. 1.2 Results derived from testing programs using these lists of challenge chemicals are not intended for the definitive characterization of protective clothing materials. 1.3 This list of challenge chemicals is not inclusive of all chemical challenges; the chemicals were chosen to represent broad ranges of liquid and gaseous chemical classes and properties. Not all chemical classes are represented. Other chemicals, especially those of interest to the manufacturer or user, should be tested in addition to those recommended in this guide.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazards statement is given in Section .