電解電容器用鋁箔檢測

電解電容器用鋁箔檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 3615-2016電解電容器用鋁箔

本標準規定了電解電容器用鋁箔的要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存及質量證明書與訂貨單(或合同)內容。本標準適用于電解電容器用中高壓陽極箔、低壓陽極箔及陰極箔(以下簡稱鋁箔)。

GB/T 31845-2015電工電子設備機械結構 熱設計規范

本標準規定了電工電子設備機械結構熱設計的基本原則、熱設計要求、常用散熱技術、關鍵散熱部件、導熱界面材料以及熱測試的相關要求，同時在附錄中介紹了熱設計算法和常用材料的物理參數。本標準適用于除手持終端以外所有電工電子設備機械結構的熱設計。以下電工電子設備簡稱“設備”，電工電子設備機械結構簡稱“機械結構”。

SJ/T 10557.1-2022電解電容器用鋁箔技術條件

本文件規定了電解電容器用鋁箔的技術要求，試驗方法，檢驗規則及標志、包裝、運輸和貯存。本文件適用于高壓電解電容器用陽極箔(以下簡稱高壓原箔)，低壓電解電容器用陽極箔(以下簡稱低壓原箔)和電解電容器用陰極箔(以下簡稱陰極箔)。

SJ/T 10557.2-1994高壓電解電容器用鋁箔晶粒織構測量方法

本標準規定了高壓電解電容器用鋁箔的織構測量方法。 本標準適用于高壓電解電容器用鋁箔。

SJ/T 10557.3-1994電解電容器用鋁箔平均位錯密度測量方法

本標準規定了電解電容器用鋁箔平均位錯密度的測量方法。 本方法適用于平均位錯密度為0～9×10^(6)個cm^(2)的電解電容器用鋁箔。

SJ/T 10557.4-1994電解電容器用鋁箔化學分析方法 原子吸收分光光度法測定 銅、鐵、鋅、錳、和鎂量

本標準規定了電解電容器用鋁箔中銅、鐵、鋅、錳和鎂的測定。 本標準適用于下列含量范圍的電解電容器用鋁箔：銅含量：0.0005～0.2000％；鐵含量：0.001～0．200%；鋅含量：0.0005～0．0200％；錳含量：0．0002～0．2000％；鎂含量：0．0001～0．0250%。

UL 399-2008飲用水冷卻器

1.1 These requirements cover self-contained drinking-water coolers which employ hermetic refrigerantmotor-compressors and which are designed for connection to alternating-current circuits rated not greaterthan 600 volts in accordance with the National Electrical Code, NFPA 70. The requirements also apply towater coolers which supply both hot and cold water.1.2 These requirements do not include additional requirements applicable to equipment designed for usein hazardous locations as defined in the National Electrical Code, NFPA 70.1.3 A product that contains features, characteristics, components, materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire, electric shock, orinjury to persons shall be evaluated using the appropriate additional component and end-productrequirements as determined necessary to maintain the acceptable level of safety as originally anticipatedby the intent of this standard. A product whose features, characteristics, components, materials, orsystems conflict with specific requirements or provisions of this standard cannot be judged to comply withthis standard. Where considered appropriate, revision of requirements shall be proposed and adopted inconformance with the methods employed for development, revision, and implementation of this standard.

UL 935-2001熒光燈鎮流器

1.1 These requirements cover ballasts of the resistance, reactance, and electronic (high frequency) types for use with fluorescent lamps involving a potential of 2500 volts or less in accordance with the National Electrical Code, ANSI/NFPA 70.1.2 A fluorescent-lamp ballast may be determined by investigation to be acceptable for use, in a fixtureor other device, with electric-discharge lamps of other than the fluorescent type.1.3 Fluorescent self ballasted lamps and ballast adaptors are evaluated using the Standard forSelf-Ballasted Lamps and Lamp Adapters, UL 1993. The component ballast is evaluated to requirementsin this Standard.1.4 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shockor injury to persons shall be evaluated using appropriate additional component and end-productrequirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

DIN EN 61360-4-2005電子元器件標準數據元素類型和相關分類模式.第4部分:IEC標準數據元素類型和元器件分類的基準集

This standard specifies:-the definitions of data element types for electric components and materials used in electrotechnical equipment and systems;-the definitions of the component classes with associated classification scheme