衛生設備流速調節器檢測

衛生設備流速調節器檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

EN 246-2003衛生設備配件.流速調節器通用規范

This European Standard specifies:the dimensional,mechanical,hydraulic and acoustic characteristics with which flow rate regulations should comply;the procedures for testing these characteristics. This European Standard is applicable to:flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets,washrooms and kitchens(single taps,combination tap assemblies,mechanical mixing valves,thermostatic mixing vavles);flow rate regulators used under the flowing pressure and temperature conditions.Flow rate regulators can only be connected downstream of the obturator of the top.

NEN-EN 246-1993衛生設備用水龍頭．流速調節器通用規范

This European Standard aims to establish:— the dimensional, hydraulic and acoustic properties to which flow rate regulators intended to be mounted on sanitary tapware shall correspond;— the test methods whereby these properties may be verified.

NEN-EN 248-1993衛生設備用水龍頭．流速調節器通用規范

This European Standard aims to establish:— the dimensional, hydraulic and acoustic properties to which flow rate regulators intended to be mounted on sanitary tapware shall correspond;— the test methods whereby these properties may be verified.

DIN EN 200-2008衛生設備用水龍頭.1型和2型的供水系統用單一水龍頭和組合水龍頭.通用技術規范

This European Standard specifies: a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in: 1) a supply system of Type 1 (see Figure 1); 2) a supply system of Type 2 (see Figure 2); b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics of nominal size 1/2 and 3/4 single taps and combination taps; c) test methods to verify the characteristics. The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.) This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks. Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar]. Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar]. This European Standard applies to sanitary draw-off taps of nominal size 1/2 and 3/4 (PN 10). The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics to be noted if the tap is used outside the recommended operating range.

BS EN 246-2003衛生設備用水龍頭.流速調節器通用規范

This European Standard specifies:n— the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;n— the procedures for testing these characteristics. This European Standard is applicable to:n— flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);n— flow rate regulators used under the following pressure and temperature conditions:nFlow rate regulators can only be connected downstream of the obturator of the tap.

ONORM EN 246-1992衛生設備管件．流速調節器通用規范

Diese Europ?ische Norm gilt für Strahlregler, die an Armaturen zur Ausrüstung von Sanit?rgegenstanden angeschlossen werden, die in R?umen für die Hygiene und Küchen eingebaut sind (Auslaufventile, Mischbatterien, mechanisch gesteuerte Mischer.. ).