混凝土加固用鋼筋 可焊鋼筋 棒材、卷材和開卷產品檢測

混凝土加固用鋼筋 可焊鋼筋 棒材、卷材和開卷產品檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 50901-2013鋼-混凝土組合結構施工規范

本規范適用于工業與民用建筑和一般構筑物的鋼-混凝土組合結構工程施工及驗收。

JB/T 8597-1997鋼筋電渣壓力焊機技術條件

本標準規定了鋼筋電渣壓力焊機的產品型式和基本參數、安全要求、技術要求、檢驗規則、標志、包裝及貯存等要求。 本標準適用于現澆鋼筋混凝土結構中，直徑范圍為14mm～40mm鋼筋豎向對接的電渣壓力焊機。用于鋼筋預埋件焊接的電焊機，亦可參照執行本標準。 按本標準要求設計的產品，僅適用于人員使用。

DIN 2626-2016線坯

This standard defines types and their facings, dimensions, materials, manufacturing processes, marking and naming of line blanks. These are made with or without bore and are used in between flange joints of piping (e. g. acc. to DIN EN 13480 series) and pressure vessels (e. g. acc. to DIN EN 13445 series). The line blanks are determined for the application with flanges acc. to DIN EN 1092-1 for nominal pressures PN 6 to PN 160 and facing type A, type B, type C and type D.

DIN 21057-10-2017制煉廠的管道等級. 第10部分: 使用1.1組材料具有高溫下特定性能的非合金和合金鋼管組件的交貨技術條件

This standard describes the technical delivery conditions and dimensions as well as the maximum allowable pressure at the maximum allowable temperature TS for the following piping components: - pipes, seamless or welded; - pipe fittings (tees, reducers, elbows, dished ends, reinforced branches and caps), - flanges Type 05 (blind flange) and Type 11 (welding neck flange); - fasteners (bolts, stud bolts, nuts and washers).

DIN 30681-2013氣體裝置用補償器. 帶不銹鋼風箱組件的擴展連接件. 安全要求, 試驗, 標記

The document specifies the requirements and tests of stainless steel expansion joints with bellow units to DN 500 and MOP 16 bar, which work with gazes according to DVGW G 260.

DIN EN 1537-2014特殊土工作業.地錨

This Standard applies to the installation and monitoring of permanent and temporary ground anchors. It covers anchors which are able to be stressed and are able to be tested in accordance with EN ISO 22477-5. The planning and design of ground anchors calls for experience and knowledge in this specialised field and although these topics are covered briefly in EN 1997-1 Eurocode 7 : Geotechnical Design, Part 1 : General Rules. This Standard does not address alternative systems of anchoring such as tension piles, screw anchors, mechanical anchors, soil nails, expander anchors or deadman anchors.

DIN EN 1994-1-2-2010歐洲規范4:復合鋼和混凝土結構的設計.第1-2部分:一般規則.結構防火設計;德文版本EN 1994-1-2-2005 + AC-2008

This part 1-2 of EN 1994 deals with the design of composite steel and concrete structures for the accidental situation of fire exposure and is intended to be used in conjunction with EN 1994-1-1 and EN 1991-2-2. This Part 1-2 only identifies differences from, or supplements to, normal temperature design.

DIN EN 10080-2005混凝土加筋用鋼.可焊性鋼筋.總則

This European Standard specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of: bars, coils (rod, wire) and decoiled products, sheets of factory made machine welded fabric, lattice girders. Steels according to this standard have a ribbed, indented or smooth surface.

DIN EN 12602-2016蒸壓加氣混凝土的預制鋼筋部件.德文版本EN 12602-2016

This European Standard is for prefabricated reinforced components of autoclaved aerated concrete to be used in building construction for: a) Structural elements: - loadbearing wall components; - retaining wall components; - roof components; - floor components; - linear components (beams and piers). b) Non-structural elements: - non-loadbearing wall components (partition walls); - cladding components (without fixtures) intended to be used for external facades of buildings; - small box culverts used to form channels for the enclosure of services; - components for noise barriers. Depending on the type and intended use of elements for which the components are utilized, the components can be applied - in addition to their loadbearing and encasing function - for purposes of fire resistance, sound insulation and thermal insulation indicated in the relevant clauses of this European Standard. Components covered by this standard are only intended to be subjected to predominantly non-dynamic actions, unless special measures are introduced in the relevant clauses of this European Standard. The term "reinforced" relates to reinforcement used for both structural and non-structural purposes. This European Standard does not cover: - rules for the application of these components in structures; - joints (except their strength and integrity E of resistance to fire); - fixtures; - finishes for external components, such as tiling. NOTE AAC components may be used in noise barriers if they are designed to fulfil also the requirements of EN 14388.

DIN EN 13670-2011混凝土結構施工;德文版本EN 13670-2009

This European Standard give common requirements for execution of concrete structures, it applies to both in-situ works and construction using prefabricated concrete elements.This standardexpects the execution specification to state all the specific requiements relevant to the particular structure.

DIN EN 14490-2010專門土工工程的執行.土釘.德文版本EN 14490-2010

This European standard establishes general principles for the construction of special geotechnical works involving soil nailing. Soil nailing is a construction technique used to enhance/maintain the stability of a soil mass by the installation of passive inclusions (soil nails).

DIN EN ISO 17660-1-2006焊接.鋼筋焊接.第1部分:承載焊接節點

This part of ISO 17660 is applicable to the welding ofweldable reinforcing steel and stainless reinforcing steel of load-bearing joints, in workshops or on site. It specifies requirements for materials, design and execution of welded joints, welding personnel, quality requirements, examination and testing.This part of ISO 17660 also covers welded joints between reinforcing steel bars and other steel components, such as connection devices and insert anchors, including prefabricated assemblies. Non load-bearing joints are covered by ISO 17660-2.This part of ISO 17660 is not applicable to factory production of welding fabric and lattice girders using multiple spot welding machines or multiple projection welding machines.The requirements of this part of ISO 17660 are only applicable to static loaded structures.NOTE For fatigue-loaded structures, depending on type of joint and welding process, it is recommended that an appropriate reduction be taken into account on the fatigue strength of the reinforcing steel.

DIN EN ISO 17660-2-2006焊接.鋼筋焊接.第2部分:非承載焊接節點

This part of ISO 17660 is applicable to the welding of weldable reinforcing steel and stainless reinforcing steel of non load-bearing welded joints, in workshops or on site. It specifies requirements for materials, design and execution of welded joints, welding personnel, quality requirements, examination and testing.Load-bearing welded joints are covered by ISO 17660-1.

BS EN 10080-2005混凝土增強用鋼.可焊接增強鋼.總則

1 This European Prestandard specifies requirements for the chemical composition and the mechanical and geometrical properties of weldable ribbed reinforcing steel in Grade B500, categories A and B (designated as steels B500A and B500B, see table 1) used for the reinforcement of concrete structures in the form ofn- bars and coils or as elements for the manufacture of welded fabric,n- sheets of factory-made machine-welded fabric in the diameter ranges given in table 1.n2 This European Prestandard does not apply ton- non-weldable reinforcing steel;n- plain round or indented reinforcing steel;n- lattice girders;n- prestressing steels (see EN 10138).

SS 560-2010混凝土用加強鋼筋規格-可焊鋼筋-棒材、卷材和開卷產品

This Singapore Standard specifies requirements for ribbed weldable reinforcing steel used for the reinforcement of concrete structures.