絕熱用噴涂硬質聚氨酯泡沫塑料檢測

絕熱用噴涂硬質聚氨酯泡沫塑料檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 20219-2015絕熱用噴涂硬質聚氨酯泡沫塑料

本標準規定了絕熱用噴涂硬質聚氨酯泡沫塑料的分類、要求、試驗方法及檢驗規則。本標準適用于建筑物或非建筑物絕熱用、服務溫度范圍-60 ℃到80 ℃的噴涂硬質聚氨酯泡沫塑料。本標準不適用于單組分聚氨酯泡沫填縫劑材料。

GB/T 21558-2008建筑絕熱用硬質聚氨酯泡沫塑料

本標準規定了建筑絕熱用硬質聚氨酯泡沫塑料的分類、要求、試驗方法、檢驗規則和標志、運輸、貯存。本標準適用于建筑絕熱用硬質聚氨酯泡沫塑料。本標準不適用于噴涂硬質聚氨酯泡沫塑料和管道用硬質聚氨酯泡沫塑料。

GB/T 25969-2010家用太陽能熱水系統主要部件選材通用技術條件

本標準規定了家用太陽能熱水系統主要部件的選材原則、技術要求、檢驗方法、檢驗規則。本標準適用于貯熱水箱容積不大于0.6m<上標 3>家用太陽能熱水系統主要部件。

GB/T 26700-2011門體填充用硬質聚氨酯泡沫塑料

本標準規定了門體填充用硬質聚氨酯泡沫塑料的分類、要求、試驗方法和檢驗規則。 本標準適用于以多元醇與多異氰酸酯為主要原料發泡生產制備,用于填充防盜門、安全門、進戶門、車庫門等門體及類似用途的硬質聚氨酯泡沫塑料。 本標準不適用于以保溫為主要用途的門體用硬質聚氨酯泡沫塑料(如冷庫門等)。

GB/T 30103.3-2013冷庫熱工性能試驗方法 第3部分:圍護結構熱流量檢測

GB/T 30103的本部分規定了土建冷庫及裝配式冷庫保溫性能中圍護結構熱流量和傳熱系數的檢測方法。本部分適用于各種類型新舊冷庫冷間隔熱性能和對能耗影響的計算。

GB/T 32270-2015壓力管道規范 動力管道

本標準規定了火力發電廠界區內以蒸汽、水和易燃易爆、有毒及腐蝕性液體或氣體為介質的管道的材料、設計、制作、安裝、檢驗、試驗、安全防護、保溫及防腐的基本要求等。其中易燃易爆、有毒及腐蝕性液體或氣體為介質的管道參照GB/T 20801。本標準不適用于下列管道：a) 鍋爐本體管道；b) 核電廠管道；c) 采暖通風與空氣調節的管道及非圓形截面的管道；d) 各種塔、建筑構架、貯罐、機械設備和儀表用的管道。本標準不包括非金屬管道的材料要求。本標準規定的管道與鍋爐本體范圍內的管道分界見圖1和圖2。

GB 50460-2015油氣輸送管道跨越工程施工規范

本規范適用于新建或改、擴建的油氣輸送管道跨越人工或天然障礙物工程的施工。不適用于沿既有橋梁敷設管道。

GB 50693-2011坡屋面工程技術規范

為提高我國坡屋面工程技術水平，確保工程質量，制定本規范。本規范適用于新建、擴建和改建的工業建筑、民用建筑坡屋面工程的設計、施工和質量驗收。坡屋面工程的設計和施工應遵守有關環境保護、建筑節能和安全的規定，并應采取相應措施。 坡屋面工程應積極采用成熟的新材料、新技術、新工藝。坡屋面工程的設計、施工和質量驗收除應符合本規范外，尚應符合現行有關標準的規定。

CJJ 28-2014城鎮供熱管網工程施工及驗收規范

本規范適用于采用明挖、暗挖、頂管、定向鉆等施工工藝,并符合下列參數的城鎮供熱管網工程的施工及驗收:1工作壓力小于或等于1.6MPa,介質溫度小于或等于350℃的蒸汽管網;2工作壓力小于或等于2.5MPa,介質溫度小于或等于200℃的熱水管網。

CJJ/T 104-2014城鎮供熱直埋蒸汽管道技術規程

本規程適用于工作壓力小于或等于2.5MPa，溫度小于或等于350°C，直接埋地敷設的鋼質外護蒸汽保溫管道的設計、施工、驗收及運行維護。

SY/T 0324-2014直埋高溫鋼質管道保溫技術規范

本規范適用于公稱直徑為50mm～1400mm，輸送介質溫度在120℃～350℃范圍內，工作管壓力不大于2. 5MPa的高溫管道保溫。

JGJ/T 181-2009房屋建筑與市政基礎設施工程檢測分類標準

本標準適用于房屋建筑和市政基礎設施工程檢測的分類。

TS ISO 8873-2-2015硬質泡沫塑料. 絕熱用噴涂硬質聚氨酯泡沫塑料. 第2部分: 應用

This part of ISO 8873 outlines requirements for the application of rigid cellular plastic spray polyurethane foam for thermal insulation.

TS ISO 8873-3-2013硬質泡沫塑料. 絕熱用噴涂硬質聚氨酯泡沫塑料. 第3部分: 試驗方法

This standard covers test methods for rigid cellular plastics of Spray-applied polyurethane foam for thermal insulation

DIN EN 13163-2017建筑物用隔熱產品.工廠制膨脹聚乙烯(EPS)產品.規格.德文版本EN 13163-2012+A2-2016

This European Standard specifies the requirements for factory made products of expanded polystyrene, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or rolls or other preformed ware. This European Standard specifies product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this European Standard are also used for sound insulation and in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required class or level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application are to be found in regulations or non conflicting standards. Products with a declared thermal resistance lower than 0,25 m2K/W or a declared thermal conductivity at 10 °C greater than 0,060 W/(mK) are not covered by this European Standard.

DIN EN 13164-2015建筑用隔熱產品.工廠制聚苯乙烯泡沫(XPS)產品.規格.德文版本EN 13164-2012+A1-2015

This European Standard specifies the requirements for factory made products of extruded polystyrene foam, with or without facings or coatings, which are used for thermal insulation of buildings. The products are manufactured in the form of boards, which are also available with special edge and surface treatment (tongue & grooves, shiplap etc.). This standard includes XPS multi-layered insulation boards with layers perpendicular to the edges of the board, i.e. layers parallel to the surface of the final board.Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.The standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.Products with a declared thermal resistance lower than 0,25 m2 K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this standard.This standard does not cover in situ insulation products, nor products intended to be used for the insulation of building equipment and industrial installations, or civil engineering applications or acoustic insulation.

DIN EN 13165-2016建筑物隔熱產品.工廠制硬質聚氨酯泡沫(PU)產品.規格.德文版本EN 13165-2012+A2-2016

This European Standard specifies the requirements for factory made rigid polyurethane foam (PU) products, with or without facings or coatings, which are used for the thermal insulation of buildings. PU includes both PIR and PUR products. The products are manufactured in the form of boards. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non conflicting standards. Products with a declared thermal resistance lower than 0,25 m2 . K/W or a declared thermal conductivity greater than 0,060 W/(m.K) at 10 °C are not covered by this European Standard. This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations (covered by EN 14308).

DIN EN 13166-2016建筑物隔熱產品.酚醛泡沫的工廠制(PF) 產品.規格.德文版本EN 13166-2012+A2-2016

This European Standard specifies the requirements for factory made phenolic foam products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards and laminates. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,40 m2K/W or a declared thermal conductivity greater than 0,050 W/(mK) at 10 °C are not covered by this standard. This standard does not cover in-situ thermal insulation products, products intended to be used for the thermal insulation of building equipment and industrial installations (covered by EN 14314 (3)).