金屬面硬質酚醛泡沫復合板檢測

金屬面硬質酚醛泡沫復合板檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 50693-2011坡屋面工程技術規范

為提高我國坡屋面工程技術水平，確保工程質量，制定本規范。本規范適用于新建、擴建和改建的工業建筑、民用建筑坡屋面工程的設計、施工和質量驗收。坡屋面工程的設計和施工應遵守有關環境保護、建筑節能和安全的規定，并應采取相應措施。 坡屋面工程應積極采用成熟的新材料、新技術、新工藝。坡屋面工程的設計、施工和質量驗收除應符合本規范外，尚應符合現行有關標準的規定。

CECS 411-2015金屬面絕熱夾芯板技術規程

本規程適用于工業與民用建筑屋面板(非上人屋面)、墻面板、天花板、內隔墻、聲屏障等的設計及安裝。

CECS 445-2016非金屬面結構保溫夾芯板設計規程

本規程適用于工業與民用建筑采用的圍護結構、輕型屋面、吊頂板等用的非金屬面結構保溫夾芯板的設計。

JC/T 1051-2018金屬面硬質酣醛泡沫復合板

本標準規定了金屬面硬質酚醛泡沫復合板產品的術語和定義、分類和標記、金屬面層材料、技術要求、試驗方法、檢驗規則以及標志、包裝、運輸和貯存。本標準適用于工業與民用建筑通風、空調系統風管用金屬面硬質酚醛泡沫復合板。

JC/T 2155-2012建筑用金屬面酚醛泡沫夾芯板

本標準規定了建筑用金屬面酚醛泡沫夾芯板產品的術語和定義、分類和標記、原材料、要求、試驗方法、檢驗規則以及包裝、運輸和貯存等。本標準適用于以彩色涂層鋼板為面層工廠化生產的工業與民用建筑外墻、隔墻、屋面、天花板的酚醛泡沫夾芯板。其他用途時可參照本標準執行。

JG/T 432-2014建筑結構保溫復合板

本標準規定了建筑結構保溫復合板的術語和定義、分類和標記、材料、要求、試驗方法、檢驗規則、標志及包裝、運輸與貯運等。本標準適用于建筑非承重圍護結構用保溫復合墻板。

JGJ/T 350-2015保溫防火復合板應用技術規程

本規程適用于新建、擴建和改建的民用建筑中采用保溫防火復合板的外墻外保溫工程的設計、施工及質量驗收。

DIN EN 13162-2015建筑物隔熱產品.工廠制礦棉(MW)制品.規格.德文版本EN 13162-2012+A1-2015

This European Standard specifies the requirements for factory made mineral wool products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the mat blankets, boards or slabs.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.Products with a declared thermal resistance lower than 0,25 m2 K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this standard. This standard does not cover in situ insulation products (covered by EN 14064 parts 1 and 2) and products intended to be used for the insulation of building equipment and industrial installations (covered by EN 14303).

DIN EN 13164-2015建筑用隔熱產品.工廠制聚苯乙烯泡沫(XPS)產品.規格.德文版本EN 13164-2012+A1-2015

This European Standard specifies the requirements for factory made products of extruded polystyrene foam, with or without facings or coatings, which are used for thermal insulation of buildings. The products are manufactured in the form of boards, which are also available with special edge and surface treatment (tongue & grooves, shiplap etc.). This standard includes XPS multi-layered insulation boards with layers perpendicular to the edges of the board, i.e. layers parallel to the surface of the final board.Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.The standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.Products with a declared thermal resistance lower than 0,25 m2 K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this standard.This standard does not cover in situ insulation products, nor products intended to be used for the insulation of building equipment and industrial installations, or civil engineering applications or acoustic insulation.

DIN EN 13166-2016建筑物隔熱產品.酚醛泡沫的工廠制(PF) 產品.規格.德文版本EN 13166-2012+A2-2016

This European Standard specifies the requirements for factory made phenolic foam products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards and laminates. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,40 m2K/W or a declared thermal conductivity greater than 0,050 W/(mK) at 10 °C are not covered by this standard. This standard does not cover in-situ thermal insulation products, products intended to be used for the thermal insulation of building equipment and industrial installations (covered by EN 14314 (3)).

DIN EN 13167-2015建筑物隔熱產品.工廠制泡沫玻璃(CG)產品.規格;德文版本EN 13167-2012+A1-2015

This European Standard specifies the requirements for factory made cellular glass (CG) products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or slabs.This standard includes CG multi-layered insulation products. Instructions of Annex C shall be followed.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.Products with a declared thermal resistance lower than 0,50 m2 K/W or a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard.This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations.

DIN EN 13168-2015建筑物用熱隔絕產品.工廠制木絲(WW)產品.規格.德文版本EN 13168-2012+A1-2015

This European Standard specifies the requirements for factory made wood wool (WW) products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or slabs.This European Standard also specifies the requirements for the factory made composite products, made from wood wool in combination with other insulation materials. This standard includes WW multilayered insulation products. Instructions of annex C shall be followed. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.Products covered by this European Standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels and classes required for a given application are to be found in regulations or non conflicting standards.Products with a declared thermal resistance lower than 0,15 m2 K/W or a declared thermal conductivity greater than 0,100 W/(m·K) at 10 °C are not covered by this standard.This European Standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations.

DIN EN 13169-2015建筑物用隔熱產品.工廠制膨脹珍珠巖(EPB)產品.規格.德文版本EN 13169-2012+A1-2015

This European standard specifies the requirements for factory made expanded perlite board (EPB) products, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards, multi layered insulation or composite insulation products.This standard includes EPB multi-layered insulation products. Instructions of Annex D shall be followed.This standard also covers composite insulation products (see Annex E).Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non conflicting standards.Products with a declared thermal resistance lower than 0,15 m2 K/W or a declared thermal conductivity greater than 0,070 W/(m·K) at 10 °C are not covered by this standard.This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations. This standard does not cover the following acoustical aspects: acoustic absorption index and direct airborne sound insulation.

DIN EN 13171-2015建筑物用隔熱產品.工廠制木纖維(WF)產品.規格.德文版本EN 13171-2012+A1-2015

This European Standard specifies the requirements for factory made wood fibre (WF) products, with or without facings or coatings, which are used for the thermal insulation of buildings ). The products are manufactured in the form of rolls, batts, felts, boards or slabs.This standard includes WF multi-layered insulation products. Instructions of Annex C shall be followed.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application are to be found in regulations or non-conflicting standards.Products with a declared thermal resistance lower than 0,20 m2 K/W or a declared thermal conductivity greater than 0,070 W/(m·K) at 10 °C are not covered by this standard.This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations.

DIN EN 13950-2014隔熱/隔音石膏復合板.定義、要求和試驗辦法.德文版本EN 13950-2014

This European Standard specifies the characteristics and performance of thermal/acoustic insulation composite panels made of an insulating material laminated to gypsum boards for which the main intended use is the internal insulation (thermal and/or acoustic) of walls. They are attached with adhesives or by mechanical fixings to vertical solid backgrounds and by mechanical fixings to wood or metal framing with the gypsum board face exposed. The method of fixing and jointing should ensure that the insulating material is not exposed in its normal application. This European Standard covers the following performance characteristics: reaction to fire, fire resistance, water vapour permeability, flexural strength, impact resistance, direct airborne sound insulation and thermal resistance to be measured according to the corresponding European test methods. It provides for the assessment and verification of constancy of performance of the products to this European Standard. This European Standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry.

DIN EN 14303-2016建筑設備和工業裝置用隔熱產品.工廠制礦物棉(MW)產品.規范;德文版本EN 14303-2015

for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0 °C to + 800 °C. Below an operating temperature of ambient, special means against water vapour diffusion and water accumulation by air flow might be required. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e. g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured with or without facings or coatings, in the form of rolls, boards, slabs, mats, felts, quilts, wired mats, lamella mats, bevelled lags and pipe sections. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure. This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.

DIN EN 14305-2016建筑設備和工業裝置用保溫制品.工廠預制泡沫玻璃(CG)制品.規范.德文版本EN 14305-2015

This European Standard specifies the requirements for factory made cellular glass products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 265 °C to + 430 °C. Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e. g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover products for the insulation of the building structure.

DIN EN 14308-2016建筑設備和工業裝置的隔熱保溫產品.硬質聚氨酯泡沫及聚異氰脲酸酯產品.規范.德文版本EN 14308-2015

This European Standard specifies the requirements for factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products, with a closed cell content not less than 90 %, with or without facings, which are used for the thermal insulation of building equipment and industrial installations, with an operating temperature range of approximately, - 200 °C to + 200 °C. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e. g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of blocks, faced or unfaced boards, pipe sections, segments and prefabricated ware. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,100 W/(m·K) at 10 °C are not covered by this European Standard. This European Standard does not cover products for in situ-insulation (spraying or dispensing) or products for the insulation of the building structure. This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.

DIN EN 14314-2016工業裝置和建筑設備用熱絕緣產品.工廠制酚醛泡沫(PF)產品規格.德文版本EN 14314-2015

This European Standard specifies the requirements for factory made phenolic foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 200 °C to + 120 °C. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e. g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of blocks, faced or unfaced, boards, pipe sections, segments and prefabricated ware. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,050 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover products for in situ-insulation (blowing or pouring) or products for the insulation of the building structure. This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.