ISO單芯絞合導體電纜檢測

ISO單芯絞合導體電纜檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

ISO 1965-1973航空器鋁電纜的鋁壓接端子

Specifies the characteristics of these components with aluminium conductors in locations in which the stabilized conductor temperature does not exceed 105 degrees centigrade. Includes information on terminology, materials, demensions, finish, inhibitors, inspection, markings, performance and installation.

ISO 1966-1973航空器電纜的壓接接頭

Describes the design requirements and tests for the crimping of insulated and non-insulated terminations to general purpose cables, with conductors of copper, copper alloy, aluminium or aluminium alloy, in locations in which the stabilized conductor temperature does not exceed the values specified for the relevant type, i. e. 105 鳦, 190 鳦 or 260 鳦. The type of cable with which the terminations are intended to be made has to be declared.

ISO 1967-1974航空器 防火電纜 尺寸、導線電阻和質量

Includes the characteristics of cables with single copper conductors, for use at a nominal voltage of 6OO V, a maximum frequency of 2 OOO Hz and a continuous temperature not exceeding 28O 鳦 (ambient temperature plus heating) but which may withstand 4OO 鳦 for a limited period. The cables will retain a certain amount of dielectric strength when subjected to a flame of 1 1OO 鳦 for 5 min.

ISO 2155-1974航空器 防火電纜 性能要求

Gives the requirements for cables for the wiring of aircraft circuits, comprising single conductors with copper core covered with nickel or any other material of equivalent properties, suitable for use at a rated voltage up to 6OO V and at a frequency not exceeding 2 OOO Hz. The cables are intended for use at a temperature which may reach 28O 鳦 in continuous service (ambient temperature plus heating) and 4OO 鳦 for a limited period.

ISO 2156-1974航空器 防火電纜 試驗方法

Specifies the tests suitable for establishing the compliance of cables with the performance requirements stated in ISO 2155. Is intended to serve as a basis for test specifications to be included in the relevant national standards when the Official Board of Inspection considers that existing tests are inadequate. The tests are classified in type tests only, type tests and routine productions tests and typ tests and production quality tests.

ISO 2360-2017非磁性導電基體上非導體覆蓋層.鍍層厚度的測量.振幅靈敏性渦流法

This document specifies a method for non-destructive measurements of the thickness of non-conductive coatings on non-magnetic electrically conductive base metals, using amplitude-sensitive eddy-current instruments. In this document, the term “coating” is used for materials such as, for example, paints and varnishes, electroplated coatings, enamel coatings, plastic coatings, claddings and powder coatings. This method is particularly applicable to measurements of the thickness of most oxide coatings produced by anodizing, but is not applicable to all conversion coatings, some of which are too thin to be measured by this method (see Clause 6). This method can also be used to measure non-magnetic metallic coatings on non-conductive base materials. However, the phase-sensitive eddy-current method specified in ISO 21968 is particularly usable to this application and can provide thickness results with a higher accuracy (see Annex A). This method is not applicable to measure non-

ISO 2574-1994航空器 電纜 識別標記

Specifies the way in which single-core, multi-core and coaxial cables used in the wiring of aircraft are to be marked as to type, size, origin, date etc. in order to facilitate servicing, the investigation of faults and replacement. Also specifies the approved methods for the marking of cores. Supplements those standards relating to marking that already exist. Allows for the codification of manufacturer's identities by individual countries.

ISO 2635-2003航空器.一般用途的飛機電纜和航空航天應用的導線.尺寸和特性

This International Standard specifies the dimensions, electrical characteristics and mechanical characteristics of multi-strand conductors for general-purpose aircraft electrical cables and aerospace applications. It applies to stranded conductors over the nominal cross-sectional area range 0,12 mm to 107 mm inclusive.nIt is not applicable to conductors for fire-resistant cables or for thermocouple extension cables. Conductors for fire-resistant cables are specified in ISO 1967 and for thermocouple extension cables are specified in ISO 8056-1.

ISO 3154-1988礦井提升用的絞合鋼絲繩 交貨的技術要求

Specifies those properties of ropes and of their component parts which form a basis for acceptance. Does not apply to full-lock coil ropes, balance ropes and flat ropes used in mines. The characteristics of the wire to be used for the manufacture of these ropes are not covered. Annex A gives an example of a works certificate; annex B gives an example of a full works certificate.This second edition cancels and replaces the first edition (1976).

ISO 3155-1976礦井提升用的絞合鋼絲繩 組成結構 特性和試驗

Specifies the nature and properties of the components together with the corresponding test methods. Describes the determination of water-soluble acids, the salt content, and the extractable content (dry matter and water content) as well as the expression of results.

ISO 3156-1976礦井提升用的絞合鋼絲繩 防銹劑、潤滑劑和維修保養 特性和試驗

Specifies the nature and properties of impregnating compounds and lubricants together with the corresponding test methods. Annex A tabulates suggested qualification and quality control tests. Annex B describes suggested test methods.

ISO 3808-2002道路車輛.無屏蔽高電壓點火電纜.總規范、試驗方法和要求

This International Standard specifies the classes, types and dimensions of, and test methods and requirements for, unscreened high-voltage ignition cables used in spark-ignited engines for road vehicles.

ISO 4024-1992道路車輛.點火線圈.低壓電纜連接

Specifies the dimensions. Applies to ignition systems for spark-ignited internal combustion engines of road vehicles.

ISO 4141-1-2019道路車輛. 多芯連接電纜. 第1部分: 基本性能鎧裝電纜的試驗方法和要求

This document specifies the test methods and requirements of basic performance multi-core sheathed cables for the connection of towing and towed vehicles, suitable for a temperature range of class A and class B defined in ISO 6722-1:2011, Table 1.

ISO 4141-2-2019道路車輛. 多芯連接電纜. 第2部分: 高性能鎧裝電纜的試驗方法和要求

This document specifies the test methods and requirements for high performance sheathed multi-core cables for the connection of towing and towed vehicles, suitable for a temperature range of class A and class B, defined in ISO 6722-1:2011, Table 1.

ISO 4141-3-2019道路車輛. 多芯連接電纜. 第3部分: 非屏蔽鎧裝低壓電纜的結構、尺寸和標記

This document specifies the construction, dimensions and marking of unscreened sheathed low-voltage multi-core cables for the connection of towing and towed vehicles, suitable for temperature range of class A and class B defined in ISO 6722-1:2011, Table 1.

ISO 4141-4-2009道路車輛.多芯連接電纜.第4部分:盤繞電纜組件的試驗方法和要求

This part of ISO 4141 specifies test method and performancenrequirements for electrical coiled cable assemblies for thenconnection of towing and towed road vehicles equipped with nominaln12 V or 24 V systems.

ISO 5828-2001電阻焊設備 連接水冷接頭的二次連接電纜 尺寸及特性

This International Standard specifies dimensions and characteristics of secondary connecting cables which are air-cooled over their length and with terminals connected to water-cooled lugs.nThe secondary connecting cables are used for connection between the secondary terminals of a welding transformer and the electrode holders.

ISO 6551-1982石油液體和氣體 動態測量的精度和可靠性 電脈沖數據和/或電子脈沖數據的電纜傳輸

Establishes guidelines for ensuring the quantities stated, a main objective being to ensure the integrity of the primary indication. In order to achieve different levels of security, criteria and recommendations for the design, installation, use and maintenance of the relevant equipment are laid down. Regulatory requirements, including those for safety, are not specifically covered in detail but certain general cautionary notes on safety are included for guidance.