海纜鎧裝用鍍鋅或鋅合金鋼絲檢測

海纜鎧裝用鍍鋅或鋅合金鋼絲檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 32795-2016海纜鎧裝用鍍鋅或鋅合金鋼絲

本標準規定了海纜鎧裝用鍍鋅或鋅合金鋼絲的術語和定義、分類和標記、訂貨內容、尺寸、外形、重量及允許偏差、技術要求、檢驗方法、檢驗規則和包裝、標志及質量證明書。本標準適用于海洋工程用光纜、電纜、光電復合纜、臍帶纜鎧裝等類似用途的鍍鋅或鋅合金圓形碳素鋼絲(以下簡稱鋼絲)。

EN ISO 13628-5-2009石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

DIN EN 10257-2-2012電力電纜或通信電纜鎧裝用鍍鋅或鋅合金非合金鋼絲.第2部分:海底電纜.德文版本EN 10257-2-2011

This European Standard specifies requirements for the properties of non-alloy zinc or zinc alloy coated steel wires used for the armouring of either submarine power or telecommunication cables.

DIN EN ISO 13628-5-2010石油和天然氣工業.水下采油系統的設計和操作.第5部分:海底纜線

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

BS EN ISO 13628-5-2009石油和天然氣工業.水下采油系統設計和操作.水下臍帶管

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.