空調風道檢測

空調風道檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 50736-2012民用建筑供暖通風與空氣調節設計規范

本規范適用于新建、改建和擴建的民用建筑的供暖、通風與空氣調節設計，不適用于有特殊用途、特殊凈化與防護要求的建筑物以及臨時性建筑物的設計。

JGJ 342-2014蒸發冷卻制冷系統工程技術規程

本規程適用于新建、擴建和改建的工業與民用建筑中采用蒸發冷卻技術的制冷工程設計、施工安裝、調試、驗收和綜合效果檢驗。

JGJ 343-2014變風量空調系統工程技術規程

本規程適用于采用全空氣變風量空調技術的工程系統設計、施工與安裝、調試、綜合效能調適和運行管理。

TB/T 3138-2018機車車輛用材料阻燃技術要求

本標準規定了鐵路機車車輛用材料阻燃技術要求及試驗方法。本標準適用于高運行速度不大于200 km/h的鐵路機車及客車。

RB/T 162-2017質量管理體系 集中空調通風系統清洗消毒服務 要求

本標準規定了集中空調通風系統清洗消毒服務質量管理體系的術語和定義、組織環境、領導作用、策劃、支持、運行、績效評價及改進。本標準適用于集中空調通風系統清洗消毒組織(以下簡稱“組織”)建立、實施、保持和改進其質量管理體系，可作為組織實施自我評價、自我聲明的依據，亦可作為對集中空調通風系統清洗消毒服務質量管理體系進行外部評價和認證的依據。

DL 5027-2015電力設備典型消防規程

本規程規定了電力設備及其相關設施的防火和滅火措施，以及消防安全管理要求，適用于發電單位、電網經營單位，以及非電力單位使用電力設備的消防安全管理。電力設計、安裝、施工、調試、生產應符合本規程的有關要求。本規程不適用于核能發電單位。

DL/T 5427-2009火力發電廠初步設計文件內容深度規定

本標準規定了火力發電廠初步設計文件編制的內容深度。本標準適用于單機容量 125MW 及以上燃用固體化石燃料,采用直接燃燒方式的新建及擴建火力發電廠的初步設計,125MW 及以下機組及改建工程參照執行。

ASTM E2816-2011防火金屬暖通和空調風道系統標準試驗方法

These test methods are intended to evaluate the ability of the HVAC duct system and its supporting construction to do the following: Resist the effects of a standardized fire exposure, and Retain its integrity. These test methods provide for the following measurements and evaluations where applicable: Ability of the fire-resistive material to resist flaming (combustion) when exposed to 1382x00B0;F (750x00B0;C). Ability of the tested support system to carry the load of the HVAC duct and its fire-resistive material(s) during a standardized fire-engulfment test. Ability of the firestops to meet the requirements of Test Method E814 when used as part of a HVAC duct system. Ability of the HVAC duct system to resist the passage of flames and hot gases onto its unexposed surface during a standardized fire-resistance test. Transmission of heat through the HVAC duct system during a standardized fire-resistance test. Ability of the firestop to resist the passage of water during a standardized hose stream test. Comparative measurement of temperature aging of the fire-resistive material(s) when subjected to a standardized thermal cycling during the durability test. Measurement of flame spread over the surface of the fire-resistive material or HVAC duct system. These test methods do not provide the following: Full information as to performance of the fire-resistive material, supporting construction, or the HVAC duct system constructed with components, densities, or dimensions other than those tested. Evaluation of the degree by which the fire-resistive material or HVAC duct system contributes to the fire hazard by generation of toxic gases, or other products of combustion. Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the HVAC duct system. The test specimens are subjected to one or more specific tests under laboratory conditions. When different test conditions are substituted or the end-use conditions are changed, it is not always possible by, or from, these test methods to predict changes to the characteristics measured. Therefore, the results of these laboratory tests are valid only for the exposure conditions described in these test methods. These test methods require a test specimen to be exposed to a standard fire that is controlled to achieve specified temperatures throughout a specified time period. The engulfment test is followed by the application of a standardized hose stream test. These test methods provide a relative measure of the fire-test-response of comparable fire-resistive materials and HVAC duct systems under these exposure conditions. The fire exposure is not representative of all fire conditions because conditions vary with changes in the amount, nature and distribution of fire loading, ventilation, compartment size and configuration, and heat sink characteristics of the compartment. Variation from the test conditions or test specimen construction, such as size, materials, method of assembly, also affects the fire-test-response. For these reasons, evaluation of the variation is required for application to construction in the field. Note 58212;When the size of the HVAC duct exceeds the capability of the test furnace to test it, the authority having jurisdiction (AHJ) should be consulted to determine what test and evaluation of the variation is required for application to construction in the field. Note 18212;Use of the standard designation ISO 6944 refers to both ISO 6944:1985 and ISO 6944-1:2008.