卷材涂料檢測

卷材涂料檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 30791-2014色漆和清漆 T彎試驗

本標準規定了一種通過在涂漆試板被彎曲時觀察其開裂或剝落的情況來評價金屬基材上有機涂層柔韌性和附著力的方法。該方法可以用于以通過/未通過試驗來評定色漆、清漆或相關產品是否符合規定的試驗要求,或者用于測定在不發生開裂情況下的小彎曲直徑。

HG/T 3830-2022預涂卷材涂料

本文件規定了預涂卷材涂料的產品分類、要求、試驗方法、檢驗規則以及標志、包裝和貯存。本文件適用于以樹脂為主要成膜物質，并加入固化劑、顏料、體質顏料、助劑等配制而成，且以連續涂裝方式涂覆在金屬薄板上的溶劑型涂料、水性涂料或粉末涂料。

JG/T 516-2017建筑裝飾用彩鋼板

本標準規定了建筑裝飾用彩鋼板的術語和定義、分類、代號、標記和示例、一般要求、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于一般工業與民用建筑室內外用彩鋼板。

ASTM D3794-2016卷材涂料的標準試驗指南

4.1x00a0;This guide represents a collection of pertinent ASTM test methods used within the coil coatings industry. In the past coil coaters world wide depended on industry standards written by the National Coil Coaters Association. That association, working cooperatively with ASTM, will no longer issue new, nor update old, standards. 1.1x00a0;This guide covers procedures for testing coil coatings. The test methods included are listed in Table 1. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Selection of test methods to be followed must be governed by the requirements in each individual case, together with agreement between the producer and user. 1.2x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

ASTM D3794-2017卷材涂料試驗的標準指南

4.1x00a0;This guide represents a collection of pertinent ASTM test methods used within the coil coatings industry. In the past coil coaters world wide depended on industry standards written by the National Coil Coaters Association. That association, working cooperatively with ASTM, will no longer issue new, nor update old, standards. 1.1x00a0;This guide covers procedures for testing coil coatings. The test methods included are listed in Table 1. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Selection of test methods to be followed must be governed by the requirements in each individual case, together with agreement between the producer and user. 1.2x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

ASTM D3794-2018卷材涂料試驗的標準指南

4.1x00a0;This guide represents a collection of pertinent ASTM test methods used within the coil coatings industry. In the past coil coaters world wide depended on industry standards written by the National Coil Coating Association. That association, working cooperatively with ASTM, will no longer issue new, nor update old, standards. 1.1x00a0;This guide covers procedures for testing coil coatings. The test methods included are listed in Table 1. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Selection of test methods to be followed must be governed by the requirements in each individual case, together with agreement between the producer and user. 1.2x00a0;The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

DIN 55945-2016油漆和清漆.DIN EN ISO 4618的附加術語和定義

This standard specifies additional terms to DIN EN ISO 4618. It is applicable to the paint industrie and users (i.e. industry, handcraft, and non-commercial end user), processing paints and varnishes. In addition, it should be the basis for (technical) publications, aministration, advertisement, expetiese, etc.

DIN EN 10300-2006近岸和海上管線用鋼管和配件.外涂層用瀝青熱涂覆材料.德文版本 EN 10300-2005

This European Standard specifies requirements for the application of factory applied external bitumen based hot applied coatings for the corrosion protection of steel tubes and fittings for onshore and offshore pipelines. The coatings described in this standard can be applied to longitudinally or spirally welded tubes or to seamless tubes and fittings used for the construction of pipelines for the conveyance of liquids or gases.

DIN EN 12258-1-2012鋁和鋁合金.術語和定義.第1部分:一般術語.三種語言版本EN 12258-1-2012

To update the terms and definitions to be used in CEN/TC 132 standards. The document defines general terms which are helpful for the communication within the aluminum industry and its customers relating to products of aluminium and aluminium alloys. Definitions in other standards applying to a particular field of application can be more specific than the definitions of identical terms in this standard; these can be found in the relevant standards.

DIN EN 16074-2019涂料和清漆. 非揮發物質含量和卷材涂料材料涂布率的測定; 德文版本EN 16074-2019

The method specifies the gravimetric procedure for determining the non-volatile-matter content as a percentage by mass of the majority of thermally cured coil coatings and subsequently for determining the theoretical spreading rate. The method is not suitable for pure epoxy coil coatings.

DS/EN 16074-2011色漆和清漆卷材涂料的不揮發物含量和涂布率的測定

The method specifies the gravimetric procedure for determining the non-volatile matter content (often referred to as dry solid or weight solids) as a percentage by mass of the majority of thermally cured coil coatings and subsequently for determining the theoretical spreading rate. The method is not suitable for pure epoxy coil coatings.