鉆井液用超細碳酸鈣檢測

鉆井液用超細碳酸鈣檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

SY/T 5725-1995鉆井液用超細碳酸鈣

本標準規定了鉆井液用超細碳酸鈣(I型和Ⅱ型)的質量指標和檢驗方法。 本標準適用于水基鉆井/完井液用酸溶性橋堵劑超細碳酸鈣。

SY/T 6395-1999重鹽水測試程序

本標準規定了重鹽水的鹽水密度、鹽水結晶溫度、鹽水清晰度測試方法，以及相關儀器的校正。 本標準適用于油田重鹽水完井液、修井液的測試方法。

DIN EN ISO 10414-2-2011石油和天然氣工業.鉆井液的現場測試.第2部分:油基液(ISO 10414-2-2011);英文版本EN ISO 10414-2-2011,僅限CD-ROM

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluid balances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

DIN EN ISO 13501-2011石油和天然氣工業.鉆井液.工藝設備的評定(ISO 13501-2011);英文版本EN ISO 13501-2011

This International Standard provides a standard procedure for assessing and modifying performance of solids control equipment systems commonly used in the field in petroleum and natural gas drilling fluids processing.

BS EN ISO 10414-2-2011石油和天然氣工業.鉆井液的現場測試.油基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-baseddrilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluidbalances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).